Inter-Tel 831.10507 Trouble -SHOOTING, Symptom the SPA will not Operate, Symptom the Pump Hums

Page 20

TROUBLE -SHOOTING

Most problems can be solved by following the simple steps below. Find the symptom that applies and follow the steps listed. If further assistance is needed, call our Customer Service Department at SEARS 1-800-4MYHOME (469-4663), or SEARS 1-877-LEFOYER (533-6937) 24 hours a day

1.SYMPTOM: THE SPA WILL NOT OPERATE

a.Check to see if the GFCI breaker is tripped or was not turned on. Reset the GFCI breaker.

b.Remove the access cover and locate the

heater switch on the side of the control box. Make sure that the heater switch is in the “on” position. Important: The spa will not operate if the heater switch is in the “off” position.

2.SYMPTOM: THE CIRCUIT BREAKER OR THE GFCI TRIPS WHILE THE SPA IS OPERATING

a.Reset the circuit breaker or the GFCI. If the cir- cuit breaker or the GFCI trips again, contact a qualified electrician for service.

3.SYMPTOM: THE PUMP HUMS

a.The filter cartridges may be dirty or damaged. Remove the cartridges from the filter housing and clean or replace the cartridges (see page 18).

b.The pump may have a foreign object stuck in

the impeller. Contact our customer service department.

c. The pump may have a loose wire connection. Contact our customer service department.

4.SYMPTOM: THE PUMP HUMS BUT DOES NOT ROTATE

a.The pump may be jammed. Contact our cus- tomer service department. If your spa is no longer under warranty, you may contact a local spa and pool service provider.

5.SYMPTOM: THE PUMP IS NOISY WHILE OPERATING

a.There may be debris in the pump. Contact our customer service department.

b.The pump may have a bad bearing. Contact

our customer service department.

6. SYMPTOM: THE WATER DOES NOT HEAT

 

a. Make

sure that the hydrotherapy spa is fully

 

covered with the spa cover.

The spa cover

must

be tight for the water to heat.

Set the

air control to low. Set the temperature to the desired setting. The water will heat at 2°F (1°C) per hour. If you are using the spa indoors, and the room temperature is maintained at

70°F (21°C), it will take approximately 24 to 36 hours for the water to reach the set

temperature.

b. If you are using the hydrotherapy spa outdoors, it may take longer for the water to heat. See the chart below for the approximate heating time.

Air T emperature

 

 

Heating T ime

70°F+ (21°C+)

 

24 to 36 hours

50°F to 70°F (10°C 21 to°C)

2 to 3 days

30°F to 50°F (1°C to 10°C)

3 to 4 days

b.If the water still has not heated after four days, contact our customer service department.

c.If actual water temperature is lower that the set

temperature, and the Heat On LED indicator on the console is not lit, contact our customer

service department.

7.SYMPTOM: THE WATER IS NOT BEING CLEANED BY THE FILTER

a.Check to see if the filter is in place. Clean the filter if it is dirty.

b.Check the chemical balance of the water. If the

pH is incorrect, the sanitizing agents will not function properly.

8.SYMPTOM: THE WATER PULSATES OR THERE IS MINIMUM WATER FLOW

a. Adjust the water level. This usually occurs only when the water level is low. Add water until the thera-jets are covered (see step 4 on page 9).

20

Image 20
Contents Model No Serial No If you require Service for thisQUESTIONS? Table of Contents Limited Five Year Hydrotherapy SPA WarrantyUse the hydrotherapy spa only as described This manual Important Safety InstructionsSpa, and it will void the warranty High or low blood pressure, circulatory prob Minimum No AWG 1.3 mmNever use the hydrotherapy spa alone Volt Minimum Breaker/Fuse 15 Amps Before YOU Begin If you set up the hydrotherapy spa inside If you set up the hydrotherapy spa outsideChoosing a Location for the Hydrotherapy SPA Hydrotherapy spa should be close to a source of waterSET-UP and Assembly One 1 phillips screwdriverWith all local, state, and national electrical codes Do not use soft waterSpa Make sure that the Spa Cover is centeredPosting the Warning Sign Starting the Hydrotherapy SPA Testing the Ground Fault Circuit Interrupter GfciTesting and Treating the Water SPA Shell Diagram SPA Operation Eight fixed thera-jetsSuction vents Suction covers in placeConsole Diagram Temperature DisplayUsing the Console Thermostat can be set to heat the water fromAdjusting the Filter Cycle Securing the SPA CoverLatch Buckle Key Attaching the RED and Blue Light CoversMaintenance Draining the Hydrotherapy SPA Water ChemistryMaintaining the Proper PH Balance Winter USE and Care Draining the PumpOpening and Closing the CUT-OFF Valves Adjusting the Filter Diverter Converting the SPA to a 240 Volt Power SourceChecking and Cleaning the Filter Maintenance Notes Symptom the SPA will not Operate Symptom the Pump HumsTrouble -SHOOTING MustSome water loss due to evaporation is normal Symptom the Water Level DropsMinimum setting. Note If the water is Part LIST-Model No Key No. Qty DescriptionExploded DRAWING-Model No Part No R1000A Ordering Replacement PartsIs a registered trademark of Icon Health & Fitness, Inc

831.10507 specifications

Inter-Tel 831.10507 is a powerful and versatile telecommunications solution designed to enhance business communication effectiveness. As part of the Inter-Tel product lineup, this device combines cutting-edge technology with user-friendly features, making it a preferred choice for many organizations.

One of the main characteristics of the Inter-Tel 831.10507 is its scalability. It supports growth by accommodating a varying number of users and can be easily expanded to meet the demands of a growing business. This scalability is particularly beneficial for small to mid-sized businesses that anticipate changes in their communication needs over time.

The device is equipped with robust voicemail capabilities. Users have access to a comprehensive voicemail system that offers personalized greetings, message storage, and retrieval options. This feature ensures that important messages are never missed, allowing businesses to maintain a high level of customer service.

In terms of connectivity, the Inter-Tel 831.10507 supports multiple communication protocols, including analog, digital, and Voice over Internet Protocol (VoIP). This extensive compatibility allows businesses to integrate the system into their existing communication infrastructure seamlessly. As a result, organizations can take advantage of both traditional and modern communication methods.

Another noteworthy feature is its call management capabilities. The Inter-Tel 831.10507 includes call forwarding, call waiting, and conference call functionalities. These features empower users to manage their calls efficiently and facilitate smoother collaboration among team members.

The system also boasts a user-friendly interface, making navigation intuitive. Users can easily configure settings, manage contacts, and access features without extensive training or technical knowledge. This ease of use reduces the time and resources spent on training staff, allowing them to focus on their core responsibilities.

Security is a critical concern for any business communication system, and the Inter-Tel 831.10507 addresses this by implementing various security protocols. These measures protect sensitive information and ensure that communications remain confidential.

Moreover, the device is designed for reliability. With a proven track record in various operational environments, it is built to withstand the challenges of day-to-day business activities.

In conclusion, the Inter-Tel 831.10507 is a sophisticated communication tool that combines scalability, advanced features, and user-friendliness. Whether for a startup or a more established company, it provides the flexibility and functionality required to enhance organizational communication, making it a worthwhile investment. By adopting this telecommunications solution, businesses can significantly improve their overall communication efficiency and effectiveness.