Harbor Freight Tools 69728 Grounding, Generator Pre-Start Checks, Checking and Filling Engine Oil

Page 8

Initial Tool Set Up/Assembly

y fet Sa

p

Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

To prevent serious injury:

Operate only with proper spark arrestor installed.

Operation of this equipment may create sparks that can start fires around dry vegetation.

A spark arrestor may be required. The operator should contact local fire agencies for laws or regulations relating to fire prevention requirements.

At high altitudes, the engine’s carburetor, governor, and any other parts that control the fuel-air ratio will need to be adjusted by a qualified mechanic to allow efficient high-altitude use and to prevent damage to the engine and any other devices used with this product.

CAUTION: This generator is not intended to power sensitive electronic equipment without the addition of an appropriate line conditioner and surge protector (both not included). Sensitive electronic equipment includes, but is not limited to, audio/video equipment, some television sets, computers, and printers. Sensitive electronic equipment should be operated on approved inverter type generators or pure sine wave generators.

Setu

Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual.

Note: Wheel Kit, item # 68531 (sold separately) can be used with this generator.

Grounding

ratiepO

The Generator must be properly grounded before use. Have the unit grounded by a qualified electrician if you are not qualified to do so.

To ground the Generator, connect a #6 AWG grounding wire (not included) from the Grounding Terminal on the Control Panel to a grounding rod (not included) that has been driven at least 24 inches deep into the earth. The grounding rod must be an earth-driven copper or brass rod (electrode) which can adequately ground the Generator.

ec

Operating Instructions

Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product.

Inspect tool before use, looking for damaged, loose, and missing parts.

If any problems are found, do not use tool until repaired.

Generator Pre-Start Checks

Maintenan

Inspect engine and equipment, looking for damaged, loose, and missing parts before set up and starting. If any problems are found, do not use equipment until fixed properly.

Checking and Filling Engine Oil

2.Close the Fuel Valve.

3.Clean the top of the Dipstick and the area around it. Remove the Dipstick by threading it counterclockwise, and wipe it off with a clean lint free rag.

CAUTION! Your Warranty is VOID if the engine’s crankcase is not properly filled with oil before each use.

Before each use, check the oil level. Do not run the engine with low or no engine oil.

Full level

Full level

Running the engine with no or low engine oil WILL permanently damage the engine.

1. Make sure the engine is stopped and is level.

4.Reinsert the Dipstick without threading it in and remove it to check the oil level. The oil level should be up to the full level as shown above.

Page 8

For Pump technical questions, please call 1-800-444-3353.

Item 69728 / 69729

For Engine technical questions, please call 1-800-520-0882.

 

 

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Item 69728 Important Safety Instructions Table of ContentsOperating Precautions SafetySetup Operation Maintenance Carbon Monoxide Hazard Using a generator indoors can KillFet Sa Setu RatiepO Maintenan Service Precautions SetupFet Sa Setu RatiepO SpecificationsComponents and Controls Safety Setup Operation Maintenance Checking and Filling Engine Oil GroundingGenerator Pre-Start Checks Checking and Filling Fuel Using the GeneratorSafety Setup RatiepO Maintenan Starting the EngineFet Sa Setu Connecting Electrical Loads Setup OperationTo Calculate Wattage EquipmentExample Stopping the Engine Under Normal Conditions Turn the Engine Switch offStopping the Engine in an Emergency Cleaning, Maintenance, and Lubrication Hr. of useChecking and Filling Fuel Engine Oil ChangeAir Filter Element Maintenance Spark Plug MaintenanceCleaning Setu RatiepO MaintenanBattery StorageFuel Lubrication10% ethanol E15, E20, E85, etc TroubleshootingDo not use gasoline with more than Use Engine will not start Compression Related section Parts List Please Read the Following CarefullySafety Setup Operation Item 69728 EPA/CARB versionItem 69729 EPA version Following parts are only onAssembly Diagram Item 69728 EPA/Carb versionFor both item numbers Manufacturer’s Warranty Coverage Owner’s Warranty ResponsibilitiesMission Oaks Blvd. PO Box 6009 Camarillo, CA 93011 800

69728 specifications

Harbor Freight Tools 69728 is a versatile and reliable tool that has garnered attention for its efficiency and user-friendly design. This tool is particularly favored by both professionals and DIY enthusiasts for its performance and affordability.

One of the standout features of the 69728 is its robust construction. Built with high-quality materials, it ensures longevity and durability, even under heavy usage conditions. This makes it ideal for various tasks, from simple household repairs to more intensive projects. Its design incorporates a rubberized grip, providing maximum comfort while reducing fatigue during extended use.

The Harbor Freight 69728 comes equipped with a powerful motor that enhances its overall performance. This motor operates smoothly, facilitating various applications without compromising speed or effectiveness. Additionally, the tool is designed to offer variable speed settings, allowing users to adjust the speed according to the requirements of their specific task. This feature adds versatility, making it suitable for intricate jobs that demand precision as well as more extensive applications that require power.

Another significant characteristic of the 69728 is its lightweight design. Weighing significantly less than comparable tools on the market, it offers ease of handling and portability. This makes it an excellent choice for those who frequently move between jobs or require a tool that can easily be transported.

Safety is a priority with the Harbor Freight 69728, and it includes several safety features that provide peace of mind during operation. The built-in safety trigger prevents accidental starts, ensuring the tool is only activated when the user intends to use it.

In terms of technological advancements, the 69728 integrates modern engineering with a focus on user efficiency. It features easy-to-use controls that are intuitive, minimizing the learning curve for beginners while still providing seasoned users with reliable functionality.

Overall, the Harbor Freight Tools 69728 stands out as a formidable option for anyone seeking a dependable and high-quality tool. Its combination of power, durability, user comfort, and safety features positions it as a valuable addition to any toolkit. Whether you are a professional contractor or a weekend hobbyist, the 69728 is engineered to meet your needs and exceed your expectations.
Top Page Image Contents