Ford 58064 owner manual Important Radio System Precautions, Correct No No No No

Page 9

Thermal Shutdown Protection - Temperature sensing electronics are used in the ESC to detect overloading and overheating of the transistor circuitry. If excessive temperature is detected, the unit automatically shuts down to prevent damage to the electronics.

2-channel radio system - The TQ 2.4GHz radio system, consisting of the receiver, the transmitter, and the servos. The system uses two channels: one to operate the throttle and one to operate the steering.

2.4GHz Spread Spectrum – This model is equipped with the latest R/C technology. Unlike AM and FM systems that require frequency crystals and are prone to frequency conflicts, the TQ 2.4GHz system automatically selects and locks onto an open frequency, and offers superior resistance to interference and “glitching.”

Voltage - Voltage is a measure of the electrical potential difference between two points, such as between the positive battery terminal and ground. Using the analogy of the garden hose, while current is the quantity of water flow in the hose, voltage corresponds to the pressure that is forcing the water through the hose.

550 and 540 - These numbers refer to the size of the motor. 550 motors have armatures that are 30% longer than 540 motors.

TRAXXAS TQ 2.4GHZ RADIO SYSTEM

IMPORTANT RADIO SYSTEM PRECAUTIONS

•Do not kink the receiver antenna wire. Kinks in the antenna wire will reduce range.

•DO NOT CUT any part of the receiver antenna wire. Cutting the antenna will reduce range.

•For maximum range, always point the front of the transmitter toward the model.

•You must extend the antenna wire in the model as far as possible for maximum range. In doing so, the antenna wire will be extended outside of the vehicle body. Do not wrap or coil the antenna wire to keep it from extending out of the body.

•The antenna wire must be installed into the antenna tube to protect it from getting cut or damaged, which will reduce range. When installing the antenna wire into the antenna tube, be careful not to kink the wire by pressing it against the antenna tube cap. The antenna wire should extend to just below or to within one-half inch below the cap.

To prevent loss of radio range, do not kink or cut the black wire, do not bend or cut the metal tip, and do not bend or cut the white wire at the end of the metal tip.

Correct No No No No

RAPTOR • 9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Model Introduction Traxxas SupportQuick Start Before YOU Proceed TraxxasMost importantly, use good common sense at all times Batteries and Battery Charging TOOLS, SUPPLIES, and Required Equipment Safety glasses5mm L wrench 0mm L wrench Joint wrench AA alkaline BatteriesAnatomy of the Raptor Electronic Speed Control Rear Camber Link LED Light PipeFront Shock Tower Quick Start Getting UP to Speed Introduction Radio and Power System TerminologyCorrect No No No No Important Radio System PrecautionsHeat Sinks Installing Transmitter Batteries Charging the Battery PackFor faster charging, the included battery may be charged at Using a Different Battery Configuration Installing the Battery PackTraxxas High-Current Connector Battery, Power Cell, 3000mAh NiMH, 7-C flatThrottle reversing procedure Steering reversing procedureRadio System Controls Steering TrimRange-Testing the Radio System Elevate the model so that the rear tires are off the groundHigher Speeds Require Greater Distance Antenna wire Setting UP the AntennaTQ 2.4GHz Binding Instructions Screw it onto the antenna postAdjusting the Electronic Speed Control Profile Description XL-5 Profile SelectionLED Codes and Protection Modes Recalibrating XL-5 Speed ControlDriving Your Model Removing and Installing Radio Gear Motor PrecautionsReceiver Installation After Running Your Vehicle in Wet ConditionsAdjusting the Toe-in Adjusting Your ModelFine Tuning the Shocks Shock Mounting PositionsGearing Compatibility Chart Adjusting the Slipper ClutchAdjusting Gear Mesh Motor and GearingMaintaining Your Model Other periodic maintenanceStorage Slipper clutch pads friction materialModel

58064 specifications

The Ford 58064 is a standout model that showcases a perfect blend of performance, technology, and utility. Designed primarily for the construction and heavy equipment sector, this versatile machine has garnered attention for its robust capabilities and innovative features.

One of the main highlights of the Ford 58064 is its powerful engine. Equipped with a high-performance diesel engine, the 58064 offers enhanced horsepower and torque, allowing it to tackle a variety of demanding tasks. This engine is engineered for efficiency, providing reliable power while optimizing fuel consumption, which is a critical consideration for any business operating heavy machinery.

In terms of design, the Ford 58064 boasts a rugged and durable construction, making it well-suited for challenging working environments. The chassis is built to withstand heavy loads and harsh conditions, ensuring longevity and reduced maintenance costs. The hydraulic system of the 58064 is another noteworthy feature. It provides excellent lifting and digging capabilities, enabling operators to complete tasks with precision and speed. The system is designed to ensure smooth operation and response, which is crucial in a fast-paced work setting.

Technologically, the Ford 58064 is equipped with advanced features that enhance usability and safety. A user-friendly control interface simplifies operation, allowing even less experienced operators to navigate the machine efficiently. Additionally, the model includes safety features such as a rollover protection system and advanced braking mechanisms that enhance operator safety on job sites.

The cab of the Ford 58064 is designed with operator comfort in mind. It offers ample space, ergonomic seating, and excellent visibility, reducing fatigue during long working hours. Enhanced climate control and sound insulation also contribute to a more pleasant working environment.

Moreover, the Ford 58064 is compatible with a variety of attachments, increasing its versatility. From backhoes to loaders and excavators, operators can customize their machine to suit specific job requirements, making it an invaluable asset to any fleet.

In conclusion, the Ford 58064 stands out in the heavy machinery market due to its powerful performance, durable design, advanced technology, and operator-friendly features. It is a reliable choice for those seeking a machine that can deliver exceptional results across various applications, making it a preferred option for contractors and construction companies alike.
Top Page Image Contents