Ford 58064 owner manual Elevate the model so that the rear tires are off the ground

Page 14

TRAXXAS TQ 2.4GHZ RADIO SYSTEM

Using Reverse: While driving, push the throttle trigger forward to apply brakes. Once stopped, return the throttle trigger to neutral. Push the throttle trigger forward again to engage proportional reverse.

7,8

USING THE RADIO SYSTEM

The TQ 2.4GHz Radio System has been adjusted at the factory for correct operation with your model. The adjustment should be checked before running the model in case of movement during shipping. Here’s how:

1. Turn the transmitter switch on. The status LED on the transmitter should be solid green (not flashing).

2. Elevate the model so that the rear tires are off the ground.

If you are holding the model, grip it firmly. Make sure your hands are clear of the moving parts of the model.

3. Plug the battery pack in the model into the speed control.

4. The on/off switch is integrated into the speed control. With the transmitter on, press the XL-5 set button for ½ second, until the LED shines red, then immediately release the button. This turns the model on (see page 16 for more on XL-5 setup and operation). To turn the XL-5 off, press the set button until the red LED turns off.

Note: If the LED shines green, Low-Voltage Detection is activated. This will cause erratic performance from the included NiMH battery pack. The default factory setting is for Low-Voltage Detection to be disabled (LED shines red). Make sure to turn the Low-Voltage Detection on when using LiPo batteries. Never use LiPo batteries while Low-Voltage Detection is turned off. See page 16 for more information.

5. Turn the steering wheel on the transmitter back and forth and check for rapid operation of the steering servo. Also, check that the steering mechanism is not loose or binding. If the steering operates slowly,

check for weak batteries.

0°

0°

6. When looking down at the

 

 

model, the front wheels

 

 

should be pointing straight

 

 

ahead. If the wheels are

 

 

turned slightly to the left

 

 

or right, slowly adjust the

 

 

steering trim control on the transmitter until they are pointing

 

straight ahead.

 

 

7.Operate the throttle trigger to ensure that you have full forward and reverse operation, and that the motor stops when the throttle trigger is at neutral.

8.Once adjustments are made, turn off your model, followed by the hand-held transmitter.

Range-Testing the Radio System

Before each running session with your model, you should range-test your radio system to ensure that it operates properly.

1.Turn on the radio system and check its operation as described in the previous section.

2.Have a friend hold the model. Make sure hands and clothing are clear of the wheels and other moving parts on the model.

3.Walk away from the model with the transmitter until you reach the farthest distance you plan to operate the model.

4.Operate the controls on the transmitter once again to be sure that the model responds correctly.

5.Do not attempt to operate the model if there is any problem with the radio system or any external interference with your radio signal at your location.

The TQ 2.4GHz transmitter has a directional antenna. For maximum range, hold the antenna upright and pointed in the direction of the model. Pointing the transmitter away from the model will reduce radio range.

Higher Speeds Require Greater Distance

The faster you drive your model, the more quickly it will near the limit of radio range. At top speeds, models can cover anywhere between 50 to 100 feet every second! It’s a thrill, but use caution to keep your model in range. If you want to see your model achieve its maximum speed, it is best to position yourself in the middle of the truck’s running area, not the far end, so you drive the truck towards and past your position. In addition to maximizing the radio’s range, this technique will keep your model closer to you, making it easier to see and control.

Your model’s radio system is designed to operate reliably up to the approximate distance that it is no longer easy or comfortable to see and control the model. Most drivers will struggle to see and drive

14 • RAPTOR

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model Quick Start IntroductionTraxxas Support Most importantly, use good common sense at all times Before YOU ProceedTraxxas Batteries and Battery Charging 5mm L wrench 0mm L wrench Joint wrench Safety glassesTOOLS, SUPPLIES, and Required Equipment AA alkaline BatteriesFront Shock Tower Anatomy of the RaptorElectronic Speed Control Rear Camber Link LED Light Pipe Quick Start Getting UP to Speed Radio and Power System Terminology IntroductionImportant Radio System Precautions Correct No No No NoHeat Sinks For faster charging, the included battery may be charged at Installing Transmitter BatteriesCharging the Battery Pack Traxxas High-Current Connector Installing the Battery PackUsing a Different Battery Configuration Battery, Power Cell, 3000mAh NiMH, 7-C flatRadio System Controls Steering reversing procedureThrottle reversing procedure Steering TrimHigher Speeds Require Greater Distance Range-Testing the Radio SystemElevate the model so that the rear tires are off the ground TQ 2.4GHz Binding Instructions Setting UP the AntennaAntenna wire Screw it onto the antenna postAdjusting the Electronic Speed Control LED Codes and Protection Modes XL-5 Profile SelectionProfile Description Recalibrating XL-5 Speed ControlDriving Your Model Receiver Installation Motor PrecautionsRemoving and Installing Radio Gear After Running Your Vehicle in Wet ConditionsFine Tuning the Shocks Adjusting Your ModelAdjusting the Toe-in Shock Mounting PositionsAdjusting Gear Mesh Adjusting the Slipper ClutchGearing Compatibility Chart Motor and GearingStorage Other periodic maintenanceMaintaining Your Model Slipper clutch pads friction materialModel

58064 specifications

The Ford 58064 is a standout model that showcases a perfect blend of performance, technology, and utility. Designed primarily for the construction and heavy equipment sector, this versatile machine has garnered attention for its robust capabilities and innovative features.

One of the main highlights of the Ford 58064 is its powerful engine. Equipped with a high-performance diesel engine, the 58064 offers enhanced horsepower and torque, allowing it to tackle a variety of demanding tasks. This engine is engineered for efficiency, providing reliable power while optimizing fuel consumption, which is a critical consideration for any business operating heavy machinery.

In terms of design, the Ford 58064 boasts a rugged and durable construction, making it well-suited for challenging working environments. The chassis is built to withstand heavy loads and harsh conditions, ensuring longevity and reduced maintenance costs. The hydraulic system of the 58064 is another noteworthy feature. It provides excellent lifting and digging capabilities, enabling operators to complete tasks with precision and speed. The system is designed to ensure smooth operation and response, which is crucial in a fast-paced work setting.

Technologically, the Ford 58064 is equipped with advanced features that enhance usability and safety. A user-friendly control interface simplifies operation, allowing even less experienced operators to navigate the machine efficiently. Additionally, the model includes safety features such as a rollover protection system and advanced braking mechanisms that enhance operator safety on job sites.

The cab of the Ford 58064 is designed with operator comfort in mind. It offers ample space, ergonomic seating, and excellent visibility, reducing fatigue during long working hours. Enhanced climate control and sound insulation also contribute to a more pleasant working environment.

Moreover, the Ford 58064 is compatible with a variety of attachments, increasing its versatility. From backhoes to loaders and excavators, operators can customize their machine to suit specific job requirements, making it an invaluable asset to any fleet.

In conclusion, the Ford 58064 stands out in the heavy machinery market due to its powerful performance, durable design, advanced technology, and operator-friendly features. It is a reliable choice for those seeking a machine that can deliver exceptional results across various applications, making it a preferred option for contractors and construction companies alike.
Top Page Image Contents