Preparing for Testing, Testing the Installation | Conair CTS 9

1	Make sure all components are installed according
	to assembly drawings. Make sure that all bolts on the saw
	have been tightened.

2	Check that saw is firmly locked into position with
	the anchoring screws.

3	Check that all wiring conforms to electrical
	codes, and all wiring covers are in place.

4	Plug in the air supply

PREPARING FOR TESTING

1

2

3

Turn on the main disconnect. Plug in the main

power cord and turn on the main disconnect.

Check that the E-Stop button is in the out, extended position.

Press the vacuum start button.

Check the rotation of the vacuum motor for correct phas- ing. (The phase in your plant may be different from the Conair factory.)

TESTING THE INSTALLATION

4

5

Press the saw start button.

Turn off the saw and vacuum.

Check the saw blade rotation.

The top of the saw blade should turn towards the front or operator side. If the top of the blade is spinning away from you or the operator side switch one of the 3-phase plug wires. Then recheck the blade rotation.

6

Make a sample cut. Restart the vacuum and the saw motor and press the manual cut button. The saw should make one sample cut.

If the saw is not working properly at any time, turn it off immediately and refer to the Troubleshooting section of this User Guide.

If you do not encounter any problems, proceed to the Operation section.

UGE058/0803

CTS Saw INSTALLATION

3-9

Image 27

Conair CTS 9, CTS 7, CTS 5 manual Preparing for Testing, Testing the Installation

Contents

Traveling Saw Date Document Number Table of Contents Troubleshooting Introduction Purpose User Guide HOW the User Guide is OrganizedYour Responsibility AS a User Read this SO no ONE Gets Hurt Read this SO no ONE Gets Hurt Turn the rotary disconnect switch to OFF or O position HOW to USE Lockout DevicePage Description Typical Applications What is HOW the CTS SAW Works SAW Works CTS SAW Features Specifications Left to right machine operation Optional EquipmentPage Installation Carefully uncrate the saw and its components Unpacking the Boxes You need these tools for installation Preparing for Installation Positioning the CTS SAW Move the saw into position. Place the saw in posiDetermine the best distance from the belt puller to Position the SAW Connecting Main Power Source Installing the Encoder Remove the hex nut Installing the SAW Blades Testing the Installation Preparing for TestingPage Operation SAW Control Control Features Machine Frame Support System Blade Height Adjustment Control Panels Upper Clamp AdjustmentPower Supply To remove and/or adjust each clamp assembly Pneumatic Cylinder Operation Electrical Operation System Inspection Machine Lubrication Wait at least five minutes for the blade to stop completely Blade Replacement Chip Collection Shrouds Blower Connection Maintenance Maintenance Features Maintenance Inspecting the blade mounting hardware Maintenance OverviewPreventative Maintenance Schedule Checking saw blades Weekly Checking Blades Checking Electrical Connections Close the electrical enclosure door Open the electrical enclosure Troubleshooting FEW Words of Caution Before Beginning Identifying Cause of a Problem Symptom Possible cause Solution Electrical Problems Extrudate Product Quality ProblemsIncorrect blade design Incorrect cooling Solenoid problem Problem Puller problemCounter problem Rodless cylinder problem Checking Servo Amplifier Check the encoder itself. There should be no play Checking the EncoderCheck all connections Check the encoder cable for damage. If neces From outside the United States, call WE’RE Here to Help Appendix A-2 Soft Keys Conair Servo Traveling Saw Numeric keys Fixed Function Keys at BottomLCD Screen Contents Starting Comms Power Up Sequence Main Screen Length CounterOn/Off Softkey Exit Softkey Reset SoftkeyTotal Softkey Total Screen Enter or Delete? Length Softkey Home Seek Homing Home Already Maint. Softkey Menu Area Maint. Area R c t n S o f t k e yChange Softkey Time Softkey S o f t k e y B l e S o f t k e y Cycles Softkey Acceptable range is 120.00-1800.00 ipm T u r n S o f t k e y 20% V a n c e S o f t k e y Menu Area Factory Softkey Error Message Table Assembly, Pneumatic / Servo GeneralBlades Opt Servo Opt. / Table Travel Equipment Parts List To Order Parts Call Toll Free 800 Volt Electrical Control, 3hp 230/460v