Checking Electrical Connections | Conair CTS 9, CTS 7, CTS 5

WARNING: Electrical hazard

Before performing any work on this product, disconnect and lock out electrical power sources to prevent injury from unexpected ener- gization or start-up. A lockable device has been provided to isolate this product from potentially hazardous electricity.

WARNING: Improper installation, oper- ation, or servicing may result in equipment damage or personal injury.

This equipment should only be installed, adjust- ed, and serviced by qualified technical person- nel who are familiar with the construction, oper- ation, and potential hazards of this type of machine.

All wiring, disconnects, and fuses should be installed by qualified electrical technicians in accordance with electrical codes in your region. Always maintain a safe ground. Do not operate the equipment at power levels other than what is specified on the machine serial tag and data plate.

1 Be sure the main power is disconnected and the saw is locked out. Always disconnect and

lock out the main power source before opening the unit or servicing.

2 Turn the main power disconnect to the off position before opening the electrical enclosure on the back of the saw or the back of the control. This is a safety device to prevent you from opening the doors if the power is still on.

CHECKING

ELECTRICAL

CONNECTIONS

Main power safety disconnect

continued on the next page

UGE058/0803

CTS Saw MAINTENANCE 5-7

Image 45

Conair CTS 9, CTS 7, CTS 5 manual Checking Electrical Connections

Contents

Traveling Saw Date Document Number Table of Contents Troubleshooting Introduction Purpose User Guide HOW the User Guide is OrganizedYour Responsibility AS a User Read this SO no ONE Gets Hurt Read this SO no ONE Gets Hurt Turn the rotary disconnect switch to OFF or O position HOW to USE Lockout DevicePage Description Typical Applications What is HOW the CTS SAW Works SAW Works CTS SAW Features Specifications Left to right machine operation Optional EquipmentPage Installation Carefully uncrate the saw and its components Unpacking the Boxes You need these tools for installation Preparing for Installation Positioning the CTS SAW Move the saw into position. Place the saw in posiDetermine the best distance from the belt puller to Position the SAW Connecting Main Power Source Installing the Encoder Remove the hex nut Installing the SAW Blades Testing the Installation Preparing for TestingPage Operation SAW Control Control Features Machine Frame Support System Blade Height Adjustment Power Supply Upper Clamp AdjustmentTo remove and/or adjust each clamp assembly Control Panels Pneumatic Cylinder Operation Electrical Operation System Inspection Machine Lubrication Wait at least five minutes for the blade to stop completely Blade Replacement Chip Collection Shrouds Blower Connection Maintenance Maintenance Features Maintenance Preventative Maintenance Schedule Maintenance OverviewChecking saw blades Inspecting the blade mounting hardware Weekly Checking Blades Checking Electrical Connections Close the electrical enclosure door Open the electrical enclosure Troubleshooting FEW Words of Caution Before Beginning Identifying Cause of a Problem Symptom Possible cause Solution Electrical Problems Incorrect blade design Product Quality ProblemsIncorrect cooling Extrudate Counter problem Problem Puller problemRodless cylinder problem Solenoid problem Checking Servo Amplifier Check all connections Checking the EncoderCheck the encoder cable for damage. If neces Check the encoder itself. There should be no play From outside the United States, call WE’RE Here to Help Appendix A-2 Soft Keys Conair Servo Traveling Saw Numeric keys Fixed Function Keys at BottomLCD Screen Contents Starting Comms Power Up Sequence Main Screen Length CounterOn/Off Softkey Total Softkey Reset SoftkeyTotal Screen Exit Softkey Enter or Delete? Length Softkey Home Seek Homing Home Already Maint. Softkey Menu Area Maint. Area R c t n S o f t k e yChange Softkey Time Softkey S o f t k e y B l e S o f t k e y Cycles Softkey Acceptable range is 120.00-1800.00 ipm T u r n S o f t k e y 20% V a n c e S o f t k e y Menu Area Factory Softkey Error Message Table Assembly, Pneumatic / Servo GeneralBlades Opt Servo Opt. / Table Travel Equipment Parts List To Order Parts Call Toll Free 800 Volt Electrical Control, 3hp 230/460v