Electrical Control, 3hp 230/460v, Volt | Conair CTS 9, CTS 7, CTS 5

EQUIPMENT PARTS LIST

TO ORDER PARTS CALL TOLL FREE (800) 458-1960

Product: CTS-5

REV #: 023525L020/0703

Instruction Manual:

Reference	Part
Number	Number	Qty	Description	3 of 3

ÿElectrical Control, 3hp 230/460v (7140360201)

40	27500675	1	Switch Assy. Disconnect
41	27501514	1	Contact, Aux. 1N.O. 1N.C.
42	20973414	1	Breaker, Circuit
43	27500202	1	Contactor, Non Rev. 12 Amp
44	27500923	1	Contacts, Aux. 2N.O. 2N.C.
45	27500109	1	Transformer, 250VA 240/480v
46	20801476	1	Receptacle, Amphenol, 4 Pin
47	20801459	1	Connector, Amphenol, 10 Pin
48	26671601	2	Relay
49	26671602	2	Relay
50	1605-30000	1	Relay, Time
51	1608-30000	7	Semi-Cond. Varistor
52	26666702	1	Connector, Cable Gland

ÿ230 Volt

53	27501510	1	Starter, 6.3-10.0 Amp
54	20604012	2	Fuse, 1.5 Amp Type FNQ
55	1646-30192	1	Receptacle, Flanged

* Indicates recommended spare parts > Indicates revisions change Italicized indicates typographical

Image 75

Conair CTS 9, CTS 7, CTS 5 manual Electrical Control, 3hp 230/460v, Volt

Contents

Traveling Saw Date Document Number Table of Contents Troubleshooting Introduction Purpose User Guide HOW the User Guide is OrganizedYour Responsibility AS a User Read this SO no ONE Gets Hurt Read this SO no ONE Gets Hurt Turn the rotary disconnect switch to OFF or O position HOW to USE Lockout DevicePage Description Typical Applications What is HOW the CTS SAW Works SAW Works CTS SAW Features Specifications Left to right machine operation Optional EquipmentPage Installation Carefully uncrate the saw and its components Unpacking the Boxes You need these tools for installation Preparing for Installation Positioning the CTS SAW Move the saw into position. Place the saw in posiDetermine the best distance from the belt puller to Position the SAW Connecting Main Power Source Installing the Encoder Remove the hex nut Installing the SAW Blades Testing the Installation Preparing for TestingPage Operation SAW Control Control Features Machine Frame Support System Blade Height Adjustment Control Panels Upper Clamp AdjustmentPower Supply To remove and/or adjust each clamp assembly Pneumatic Cylinder Operation Electrical Operation System Inspection Machine Lubrication Wait at least five minutes for the blade to stop completely Blade Replacement Chip Collection Shrouds Blower Connection Maintenance Maintenance Features Maintenance Inspecting the blade mounting hardware Maintenance OverviewPreventative Maintenance Schedule Checking saw blades Weekly Checking Blades Checking Electrical Connections Close the electrical enclosure door Open the electrical enclosure Troubleshooting FEW Words of Caution Before Beginning Identifying Cause of a Problem Symptom Possible cause Solution Electrical Problems Extrudate Product Quality ProblemsIncorrect blade design Incorrect cooling Solenoid problem Problem Puller problemCounter problem Rodless cylinder problem Checking Servo Amplifier Check the encoder itself. There should be no play Checking the EncoderCheck all connections Check the encoder cable for damage. If neces From outside the United States, call WE’RE Here to Help Appendix A-2 Soft Keys Conair Servo Traveling Saw Numeric keys Fixed Function Keys at BottomLCD Screen Contents Starting Comms Power Up Sequence Main Screen Length CounterOn/Off Softkey Exit Softkey Reset SoftkeyTotal Softkey Total Screen Enter or Delete? Length Softkey Home Seek Homing Home Already Maint. Softkey Menu Area Maint. Area R c t n S o f t k e yChange Softkey Time Softkey S o f t k e y B l e S o f t k e y Cycles Softkey Acceptable range is 120.00-1800.00 ipm T u r n S o f t k e y 20% V a n c e S o f t k e y Menu Area Factory Softkey Error Message Table Assembly, Pneumatic / Servo GeneralBlades Opt Servo Opt. / Table Travel Equipment Parts List To Order Parts Call Toll Free 800 Volt Electrical Control, 3hp 230/460v