Manuals / Conair / Power Tools / Saw

Conair CTS 7, CTS 9 Positioning the CTS SAW, Move the saw into position. Place the saw in posi

Models: CTS 5 CTS 9 CTS 7

1 75

Download 75 pages 26.28 Kb

Page 22

POSITIONING THE CTS SAW

1

Move the saw into position. Place the saw in posi-

tion downstream of the belt puller.

CAUTION: Lifting

To avoid personal injury or damage to the saw, lift the saw using a forklift or hoist with straps that have been positioned at the saw's center of gravity.

Saw

2

Determine the best distance from the belt puller to

the CTS Saw.

3

4

●For flexible products, the saw should be as close as possible to the puller.

●For rigid products, leave enough space to allow the product to flex during the cutting cycle. In some cases, it may be necessary to allow 6-8 feet between the puller and saw.

Align the saw with the extrusion line.

Measure the centerline height of the extrudate as it exits the extrusion die. Adjust all equipment on the extrusion line (sizing tank, cooling tanks, belt puller, and saw) to this height.

continued on the next page

3-4

INSTALLATION

CTS Saw

UGE058/0803

Image 22

Conair CTS 7, CTS 9, CTS 5 manual Positioning the CTS SAW, Move the saw into position. Place the saw in posi

Contents

Traveling Saw Date Document Number Table of Contents Troubleshooting Introduction HOW the User Guide is Organized Purpose User GuideYour Responsibility AS a User Read this SO no ONE Gets Hurt Read this SO no ONE Gets Hurt HOW to USE Lockout Device Turn the rotary disconnect switch to OFF or O positionPage Description What is Typical ApplicationsHOW the CTS SAW Works SAW Works Features CTS SAWSpecifications Optional Equipment Left to right machine operationPage Installation Unpacking the Boxes Carefully uncrate the saw and its componentsPreparing for Installation You need these tools for installationMove the saw into position. Place the saw in posi Positioning the CTS SAWDetermine the best distance from the belt puller to Position the SAW Connecting Main Power Source Installing the Encoder Installing the SAW Blades Remove the hex nutPreparing for Testing Testing the InstallationPage Operation SAW Control Control Features Blade Height Adjustment Machine Frame Support SystemTo remove and/or adjust each clamp assembly Upper Clamp AdjustmentPower Supply Control PanelsPneumatic Cylinder Operation Electrical Operation Machine Lubrication System InspectionBlade Replacement Wait at least five minutes for the blade to stop completelyChip Collection Shrouds Blower Connection Maintenance Maintenance Features Maintenance Checking saw blades Maintenance OverviewPreventative Maintenance Schedule Inspecting the blade mounting hardwareWeekly Checking Blades Checking Electrical Connections Open the electrical enclosure Close the electrical enclosure doorTroubleshooting Before Beginning FEW Words of CautionIdentifying Cause of a Problem Electrical Problems Symptom Possible cause SolutionIncorrect cooling Product Quality ProblemsIncorrect blade design ExtrudateRodless cylinder problem Problem Puller problemCounter problem Solenoid problemChecking Servo Amplifier Check the encoder cable for damage. If neces Checking the EncoderCheck all connections Check the encoder itself. There should be no playWE’RE Here to Help From outside the United States, callAppendix A-2 Conair Servo Traveling Saw Soft KeysFixed Function Keys at Bottom Numeric keysLCD Screen Contents Power Up Sequence Starting CommsLength Counter Main ScreenOn/Off Softkey Total Screen Reset SoftkeyTotal Softkey Exit SoftkeyLength Softkey Enter or Delete?Homing Home SeekHome Already Menu Area Maint. SoftkeyR c t n S o f t k e y Maint. AreaChange Softkey S o f t k e y Time SoftkeyCycles Softkey B l e S o f t k e yT u r n S o f t k e y Acceptable range is 120.00-1800.00 ipmV a n c e S o f t k e y 20%Error Message Menu Area Factory SoftkeyGeneral Table Assembly, Pneumatic / ServoBlades Opt Equipment Parts List To Order Parts Call Toll Free 800 Servo Opt. / Table TravelElectrical Control, 3hp 230/460v Volt