HOW to USE Lockout Device | Conair CTS 9, CTS 7, CTS 5 guide

WARNING: Electrical hazard

Before performing maintenance or repairs on this product, disconnect and lock out electrical power sources to prevent injury from unexpect- ed energization or start-up. A lockable device has been provided to isolate this product from potentially hazardous electricity.

Lockout is the preferred method of isolating machines or equipment from energy sources. Your Conair product is equipped with the lockout device pictured below. To use the lockout device:

1 Stop or turn off the equipment.

2	Isolate the equipment from
	electrical power.
	Turn the rotary disconnect switch to	O
	OFF or O position.
3	Secure the device with an
	assigned lock or tag.

4 The equipment is now locked out.

HOW TO USE

THE LOCKOUT

DEVICE

CAUTION: Moving parts

Before removing lockout devices and returning switches to the ON position, make sure that all personnel are clear of the machine, tools have been removed and all safety guards are rein- stalled.

UGE058/0803

CTS Saw

INTRODUCTION 1-5

Image 9

Conair CTS 9, CTS 7, CTS 5 manual HOW to USE Lockout Device, Turn the rotary disconnect switch to OFF or O position

Contents

Traveling Saw Date Document Number Table of Contents Troubleshooting Introduction Purpose User Guide HOW the User Guide is OrganizedYour Responsibility AS a User Read this SO no ONE Gets Hurt Read this SO no ONE Gets Hurt Turn the rotary disconnect switch to OFF or O position HOW to USE Lockout DevicePage Description Typical Applications What is HOW the CTS SAW Works SAW Works CTS SAW Features Specifications Left to right machine operation Optional EquipmentPage Installation Carefully uncrate the saw and its components Unpacking the Boxes You need these tools for installation Preparing for Installation Positioning the CTS SAW Move the saw into position. Place the saw in posiDetermine the best distance from the belt puller to Position the SAW Connecting Main Power Source Installing the Encoder Remove the hex nut Installing the SAW Blades Testing the Installation Preparing for TestingPage Operation SAW Control Control Features Machine Frame Support System Blade Height Adjustment Power Supply Upper Clamp AdjustmentTo remove and/or adjust each clamp assembly Control Panels Pneumatic Cylinder Operation Electrical Operation System Inspection Machine Lubrication Wait at least five minutes for the blade to stop completely Blade Replacement Chip Collection Shrouds Blower Connection Maintenance Maintenance Features Maintenance Preventative Maintenance Schedule Maintenance OverviewChecking saw blades Inspecting the blade mounting hardware Weekly Checking Blades Checking Electrical Connections Close the electrical enclosure door Open the electrical enclosure Troubleshooting FEW Words of Caution Before Beginning Identifying Cause of a Problem Symptom Possible cause Solution Electrical Problems Incorrect blade design Product Quality ProblemsIncorrect cooling Extrudate Counter problem Problem Puller problemRodless cylinder problem Solenoid problem Checking Servo Amplifier Check all connections Checking the EncoderCheck the encoder cable for damage. If neces Check the encoder itself. There should be no play From outside the United States, call WE’RE Here to Help Appendix A-2 Soft Keys Conair Servo Traveling Saw Numeric keys Fixed Function Keys at BottomLCD Screen Contents Starting Comms Power Up Sequence Main Screen Length CounterOn/Off Softkey Total Softkey Reset SoftkeyTotal Screen Exit Softkey Enter or Delete? Length Softkey Home Seek Homing Home Already Maint. Softkey Menu Area Maint. Area R c t n S o f t k e yChange Softkey Time Softkey S o f t k e y B l e S o f t k e y Cycles Softkey Acceptable range is 120.00-1800.00 ipm T u r n S o f t k e y 20% V a n c e S o f t k e y Menu Area Factory Softkey Error Message Table Assembly, Pneumatic / Servo GeneralBlades Opt Servo Opt. / Table Travel Equipment Parts List To Order Parts Call Toll Free 800 Volt Electrical Control, 3hp 230/460v