Ford 58064 Installing the Battery Pack, Radio System Rules, Traxxas High-Current Connector

Page 12

TRAXXAS TQ 2.4GHZ RADIO SYSTEM

INSTALLING THE BATTERY PACK

The following Traxxas High- Current Connector packages are available from your hobby dealer. When using adapters, be careful not to exceed the current rating of the Molex connector.

Part #3060

Part #3080

Single Male/Female

2-Pack Female

Part #3061

Part #3070

Male Charge Adapter

2-Pack Male

Part #3062

Female Charge Adapter

Install the battery pack with the battery wires facing the rear of the model. Insert the tabs of the battery hold-down into the slots in the rear hold-down retainer and then place the battery hold- down over the post. Secure the battery hold-down with a body clip in the hole in the post. Do not connect the battery pack yet.

Using a Different

Battery Configuration

The battery hold-downs are capable of accommodating either side-by- side racing style packs or the more common stick packs. The battery compartments are configured for stick packs from the factory. The number on each side of the hold down indicates the battery height in millimeters that hold-down can accommodate. Note that one side is labeled “25” and the other side is labeled “23”. The 25mm side is for use with typical stick type battery packs. If you are using side-by-side racing packs, simply flip the hold-down over to the 23mm side and use it on the opposite side of the chassis. Your model includes a foam block which should be installed in front of 6-cell batteries for a more secure fit.

25mm side: Standard NiMH stick pack setup

23mm side: Side-by-side

NiMH pack setup

Using Other Batteries

Your model is equipped with a state of the art, high-performance power system. It is designed to be able to flow large amounts of

power with the least amount of restriction. The benefits are drastically

increased speed and acceleration. However, this places extra

demands on the battery and electrical system connections. For best

performance, your model requires the use of NiMH battery packs that

have cells rated for high discharge and use high-quality, low-resistance

assembly techniques, such as the included Traxxas Power Cell Battery

Pack. Cheaply made battery packs do not retain their performance

characteristics after repeated uses in high-powered electric applications.

They will lose their punch and run time and may require frequent replacement. In addition, poor-quality, high-resistance cell connectors could fail, requiring disassembly and repair. The main goal is to reduce all sources of high resistance in the pack. This includes the connector, the wire, and the bars attaching the cells together.

High pack resistance will create additional heat and rob you of the full power the cells are capable of producing. We recommend using Traxxas Power Cell batteries for best performance.

2923 Battery, Power Cell, 3000mAh (NiMH, 7-C flat, 8.4V)

2940 Battery, Series 3 Power Cell, 3300mAh (NiMH, 7-C flat, 8.4V) 2950 Battery, Series 4 Power Cell, 4200mAh (NiMH, 7-C flat, 8.4V)

RADIO SYSTEM RULES

•Always turn your transmitter on first and off last. This procedure will help to prevent your model from receiving stray signals from another transmitter, or other source, and running out of control. Your model has electronic fail-safes to prevent this type of malfunction, but the first, best defense against a runaway model is to always turn the transmitter on first and off last.

•Always turn on the transmitter before plugging in the battery.

5

12 • RAPTOR

The Traxxas High-Current Connector

Your model is equipped with the Traxxas High- Current Connector. Standard connectors restrict current flow and are not capable of delivering the power needed to maximize the output of the XL-5.

The Traxxas connector’s gold-plated terminals with large contact surfaces ensure positive current flow with the least amount of resistance. Secure, long-lasting, and easy to grip, the Traxxas connector is engineered to extract all the power your battery has to give.

12

Always turn your

Plug in the battery.

transmitter on first.

 

3

Turn on the model.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Model Introduction Traxxas SupportQuick Start Before YOU Proceed TraxxasMost importantly, use good common sense at all times Batteries and Battery Charging Safety glasses TOOLS, SUPPLIES, and Required Equipment5mm L wrench 0mm L wrench Joint wrench AA alkaline BatteriesAnatomy of the Raptor Electronic Speed Control Rear Camber Link LED Light PipeFront Shock Tower Quick Start Getting UP to Speed Radio and Power System Terminology IntroductionImportant Radio System Precautions Correct No No No NoHeat Sinks Installing Transmitter Batteries Charging the Battery PackFor faster charging, the included battery may be charged at Installing the Battery Pack Using a Different Battery ConfigurationTraxxas High-Current Connector Battery, Power Cell, 3000mAh NiMH, 7-C flatSteering reversing procedure Throttle reversing procedureRadio System Controls Steering TrimRange-Testing the Radio System Elevate the model so that the rear tires are off the groundHigher Speeds Require Greater Distance Setting UP the Antenna Antenna wireTQ 2.4GHz Binding Instructions Screw it onto the antenna postAdjusting the Electronic Speed Control XL-5 Profile Selection Profile DescriptionLED Codes and Protection Modes Recalibrating XL-5 Speed ControlDriving Your Model Motor Precautions Removing and Installing Radio GearReceiver Installation After Running Your Vehicle in Wet ConditionsAdjusting Your Model Adjusting the Toe-inFine Tuning the Shocks Shock Mounting PositionsAdjusting the Slipper Clutch Gearing Compatibility ChartAdjusting Gear Mesh Motor and GearingOther periodic maintenance Maintaining Your ModelStorage Slipper clutch pads friction materialModel

58064 specifications

The Ford 58064 is a standout model that showcases a perfect blend of performance, technology, and utility. Designed primarily for the construction and heavy equipment sector, this versatile machine has garnered attention for its robust capabilities and innovative features.

One of the main highlights of the Ford 58064 is its powerful engine. Equipped with a high-performance diesel engine, the 58064 offers enhanced horsepower and torque, allowing it to tackle a variety of demanding tasks. This engine is engineered for efficiency, providing reliable power while optimizing fuel consumption, which is a critical consideration for any business operating heavy machinery.

In terms of design, the Ford 58064 boasts a rugged and durable construction, making it well-suited for challenging working environments. The chassis is built to withstand heavy loads and harsh conditions, ensuring longevity and reduced maintenance costs. The hydraulic system of the 58064 is another noteworthy feature. It provides excellent lifting and digging capabilities, enabling operators to complete tasks with precision and speed. The system is designed to ensure smooth operation and response, which is crucial in a fast-paced work setting.

Technologically, the Ford 58064 is equipped with advanced features that enhance usability and safety. A user-friendly control interface simplifies operation, allowing even less experienced operators to navigate the machine efficiently. Additionally, the model includes safety features such as a rollover protection system and advanced braking mechanisms that enhance operator safety on job sites.

The cab of the Ford 58064 is designed with operator comfort in mind. It offers ample space, ergonomic seating, and excellent visibility, reducing fatigue during long working hours. Enhanced climate control and sound insulation also contribute to a more pleasant working environment.

Moreover, the Ford 58064 is compatible with a variety of attachments, increasing its versatility. From backhoes to loaders and excavators, operators can customize their machine to suit specific job requirements, making it an invaluable asset to any fleet.

In conclusion, the Ford 58064 stands out in the heavy machinery market due to its powerful performance, durable design, advanced technology, and operator-friendly features. It is a reliable choice for those seeking a machine that can deliver exceptional results across various applications, making it a preferred option for contractors and construction companies alike.
Top Page Image Contents