Fisher CZ-3D manual Battery Replacement

Page 29

BATTERY REPLACEMENT

Check your batteries frequently by clicking the SENSITIVITY control counter clockwise into the BATT test position. The condition of the batteries will be indicated in two ways:

1)An Audio Tone. The stronger the better. A loud, high-pitched tone indicates good batteries. A weak, low-pitched tone indicates weak batteries.

2)A Meter Reading. Replace the batteries when the needle falls below gray BATT area. Two nine volt transistor batteries are located in a compartment at the rear of the housing. Always replace both batteries at the same time. You may also use rechargeable Nicads but expect about 1/2 the battery life of an alkaline battery.

1.Remove the battery door by loosening the two captive screws.

2.Tilt the housing slightly and the batteries will slide out.

3.Install the new batteries. Make sure the contact end goes in first and that you match the polarity markings on the battery door.

If either or both of the batteries are installed incorrectly, the CZ-3D will not turn on. The instrument will not be damaged.

4.Finger tighten the screws down snugly. Do not use a screwdriver or other hand tool.

Figure 9. BATTERY REPLACEMENT

27

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Maximized For finding older era Coins At older sites Contents About Your Detector Factory PRE-SET TURN-ON-AND-GO Marks Ground = 5 Disc = Sensitivity = 3 Mode = Enhance Volume =Condensed Operating Instructions Fisher CZ-3D Setting UPSetting UP Control Panel HipmountingControl Panel Control PanelSensitivity = Mode =ENHANCE Volume = OFF Turn on ProcedureGround Balancing Ground =Pushbutton Ground Balance Method Bobbing the Search Coil MethodBobbing the Search Coil Method Search Modes Target ID Search Mode Search Modes Autotune Search ModeSearch Modes Search Modes Typical CZ-3D Audio and Meter Reponses TARGET/REAL World Search Modes Supplement A. TOM Dankowskis Enhanced ID ChartSearching Searching Pinpointing Pushbutton Pinpoint ModePinpointing Target ID and Autotune Modes Target IdentificationTarget Identification Target Identification Depth Reading Target Recovery False Signals Recovery ToolsFalse Signals MaintenanceLets Preserve OUR Treasured Sport Treasure HUNTERS’ Code of EthicsBattery Replacement Battery ReplacementWeight SPECIFICATIONS1Concentric, Co-planar Spider Coil Quality

CZ-3D specifications

The Fisher CZ-3D is a highly respected metal detector renowned for its sensitivity and versatility, particularly among treasure hunters and coin collectors. Fisher Laboratories, with a rich history in the metal detection industry, developed the CZ-3D to cater to more experienced users who seek depth, precision, and advanced features in their detecting devices.

One of the main features of the CZ-3D is its ability to detect both ferrous and non-ferrous metals with exceptional accuracy. This dual function allows users to identify a wider variety of targets, from coins and jewelry to relics and artifacts. The CZ-3D is specifically tuned to recognize the nuanced differences among targets, which significantly improves the detectorist's chances of locating valuable finds while ignoring unwanted trash.

The CZ-3D employs an advanced discrimination system that expertly filters out undesirable metals. This is particularly valuable when hunting in trashy areas where targets can be closely situated. The device features a unique “3D” mode, which aids in evaluating targets before they are unearthed. This mode also allows user to experience a more intuitive understanding of the ground conditions and target depths, enhancing overall efficiency.

Another notable characteristic of the CZ-3D is its exceptional depth performance. It utilizes a dual-frequency technology, operating at both 5 kHz and 15 kHz. This capability enables the detector to achieve greater penetration into the ground, providing the ability to locate deeper targets that many other detectors might miss. This is especially useful in areas with high mineralization where standard detectors may struggle.

Ergonomics also play a crucial role in the design of the CZ-3D. The device features a lightweight construction that ensures comfortable usage over extended periods. The adjustable shaft and user-friendly control layout allow for easy customization to suit individual preferences. Users can conveniently access settings such as sensitivity and discrimination levels, enhancing the overall user experience.

Water-resistant components make the CZ-3D suitable for various hunting environments, allowing operations in wet or humid conditions. This versatility broadens the scope of potential searching locations, from beaches and parks to rivers and fields.

In summary, the Fisher CZ-3D is distinguished by its powerful detection capabilities, advanced discrimination features, dual-frequency technology, and ergonomic design. For serious treasure hunters and coin collectors, the CZ-3D represents a dependable tool that combines innovation with practicality, making it a preferred choice for those aiming to uncover hidden treasures beneath the earth.
Top Page Image Contents