Fisher CZ-3D manual Setting UP

Page 6

SETTING UP

5.With the stem length properly adjusted, wrap the loop cable tightly around the center section stem and secure it with the two Velcro straps. Connect the cable connector to the control housing.

CAUTION: Make sure that the cable is not pulled tight at the control housing and that you have enough slack at the search coil to adjust it to any angle.

6.With the shaft length and coil angle properly adjusted, you should be able to move into your “search” position (as shown in illustration below) by leaning forward very slightly and raising your arm (still straight) until the search coil is about 2 inches above the ground and 12 inches in front of your foot. The search coil should be parallel to the ground and may have to be slightly readjusted at this point.

Figure 2. SEARCH POSITION. Adjust the stem length and coil angle so the coil rests flat on the ground about 6 to 12 inches in front of your foot. Move into your “search” position by leaning forward slightly and raising the coil about 2 inches off the ground. This should put the search coil out about 12 to 18 inches in front of your foot.

4

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Maximized For finding older era Coins At older sites Contents About Your Detector Ground = 5 Disc = Sensitivity = 3 Mode = Enhance Volume = Condensed Operating InstructionsFactory PRE-SET TURN-ON-AND-GO Marks Setting UP Fisher CZ-3DSetting UP Hipmounting Control PanelControl Panel Control PanelGround Balancing Turn on ProcedureSensitivity = Mode =ENHANCE Volume = OFF Ground =Bobbing the Search Coil Method Pushbutton Ground Balance MethodBobbing the Search Coil Method Search Modes Search Modes Autotune Search Mode Target ID Search ModeSearch Modes Search Modes Typical CZ-3D Audio and Meter Reponses Search Modes Supplement A. TOM Dankowskis Enhanced ID Chart TARGET/REAL WorldSearching Searching Pushbutton Pinpoint Mode PinpointingTarget Identification Pinpointing Target ID and Autotune ModesTarget Identification Target Identification Depth Reading Target Recovery Recovery Tools False SignalsMaintenance False SignalsTreasure HUNTERS’ Code of Ethics Lets Preserve OUR Treasured SportBattery Replacement Battery ReplacementSPECIFICATIONS1 WeightConcentric, Co-planar Spider Coil Quality

CZ-3D specifications

The Fisher CZ-3D is a highly respected metal detector renowned for its sensitivity and versatility, particularly among treasure hunters and coin collectors. Fisher Laboratories, with a rich history in the metal detection industry, developed the CZ-3D to cater to more experienced users who seek depth, precision, and advanced features in their detecting devices.

One of the main features of the CZ-3D is its ability to detect both ferrous and non-ferrous metals with exceptional accuracy. This dual function allows users to identify a wider variety of targets, from coins and jewelry to relics and artifacts. The CZ-3D is specifically tuned to recognize the nuanced differences among targets, which significantly improves the detectorist's chances of locating valuable finds while ignoring unwanted trash.

The CZ-3D employs an advanced discrimination system that expertly filters out undesirable metals. This is particularly valuable when hunting in trashy areas where targets can be closely situated. The device features a unique “3D” mode, which aids in evaluating targets before they are unearthed. This mode also allows user to experience a more intuitive understanding of the ground conditions and target depths, enhancing overall efficiency.

Another notable characteristic of the CZ-3D is its exceptional depth performance. It utilizes a dual-frequency technology, operating at both 5 kHz and 15 kHz. This capability enables the detector to achieve greater penetration into the ground, providing the ability to locate deeper targets that many other detectors might miss. This is especially useful in areas with high mineralization where standard detectors may struggle.

Ergonomics also play a crucial role in the design of the CZ-3D. The device features a lightweight construction that ensures comfortable usage over extended periods. The adjustable shaft and user-friendly control layout allow for easy customization to suit individual preferences. Users can conveniently access settings such as sensitivity and discrimination levels, enhancing the overall user experience.

Water-resistant components make the CZ-3D suitable for various hunting environments, allowing operations in wet or humid conditions. This versatility broadens the scope of potential searching locations, from beaches and parks to rivers and fields.

In summary, the Fisher CZ-3D is distinguished by its powerful detection capabilities, advanced discrimination features, dual-frequency technology, and ergonomic design. For serious treasure hunters and coin collectors, the CZ-3D represents a dependable tool that combines innovation with practicality, making it a preferred choice for those aiming to uncover hidden treasures beneath the earth.
Top Page Image Contents