Fisher manual Setting UP, Fisher CZ-3D

Page 5

SETTING UP

Drop-in battery compartments

Adjustable

and cable connector at rear of

non-metallic

housing(not shown)

lower stem

Removable control

Center

section

housing (belt loop on

 

underside of housing)

 

Foam hand grip

 

Padded arm rest

Upper

lock nut Lower lock nut

Seven foot search coil cable

Upper stem

8-inch Spider

search coil

Nylon wing nut

(replacable

Duro-Neoprene

bushings, not

shown)

Built-in detector stand

Figure 1. FISHER CZ-3D

The CZ-3D comes to you just about ready to use. Take a look at the diagram above and familiarize yourself with the parts of the CZ-3D before proceeding.

1.Unpack your new CZ-3D carefully. Save the carton and inserts for future storage or shipment.

2.Take a look inside the locknut on the upper stem. Note the clear plastic locking pad on the left hand side and loosen the lock nut by rotating it fully counterclockwise.

3.Slip the lower stem into the center section.

4.Adjust the stem length (using the guide pin & stem lock nut) and the coil angle (using the nylon wing nut) so the search coil rests flat on the ground about 6 inches in front of, and slightly to the right of your right foot, (to the left of your left foot for left handers). Your arm should be straight and relaxed, with the grip held loosely.

REMEMBER: The longer the shaft, the more you will have to bend your elbow and the sooner your arm will get tired. The CZ-3D is balanced for comfortable searching in a tight semicircle around the front of the operator.

3

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Maximized For finding older era Coins At older sites Contents About Your Detector Factory PRE-SET TURN-ON-AND-GO Marks Ground = 5 Disc = Sensitivity = 3 Mode = Enhance Volume =Condensed Operating Instructions Fisher CZ-3D Setting UPSetting UP Control Panel HipmountingControl Panel Control PanelSensitivity = Mode =ENHANCE Volume = OFF Turn on ProcedureGround Balancing Ground =Pushbutton Ground Balance Method Bobbing the Search Coil MethodBobbing the Search Coil Method Search Modes Target ID Search Mode Search Modes Autotune Search ModeSearch Modes Search Modes Typical CZ-3D Audio and Meter Reponses TARGET/REAL World Search Modes Supplement A. TOM Dankowskis Enhanced ID ChartSearching Searching Pinpointing Pushbutton Pinpoint ModePinpointing Target ID and Autotune Modes Target IdentificationTarget Identification Target Identification Depth Reading Target Recovery False Signals Recovery ToolsFalse Signals MaintenanceLets Preserve OUR Treasured Sport Treasure HUNTERS’ Code of EthicsBattery Replacement Battery ReplacementWeight SPECIFICATIONS1Concentric, Co-planar Spider Coil Quality

CZ-3D specifications

The Fisher CZ-3D is a highly respected metal detector renowned for its sensitivity and versatility, particularly among treasure hunters and coin collectors. Fisher Laboratories, with a rich history in the metal detection industry, developed the CZ-3D to cater to more experienced users who seek depth, precision, and advanced features in their detecting devices.

One of the main features of the CZ-3D is its ability to detect both ferrous and non-ferrous metals with exceptional accuracy. This dual function allows users to identify a wider variety of targets, from coins and jewelry to relics and artifacts. The CZ-3D is specifically tuned to recognize the nuanced differences among targets, which significantly improves the detectorist's chances of locating valuable finds while ignoring unwanted trash.

The CZ-3D employs an advanced discrimination system that expertly filters out undesirable metals. This is particularly valuable when hunting in trashy areas where targets can be closely situated. The device features a unique “3D” mode, which aids in evaluating targets before they are unearthed. This mode also allows user to experience a more intuitive understanding of the ground conditions and target depths, enhancing overall efficiency.

Another notable characteristic of the CZ-3D is its exceptional depth performance. It utilizes a dual-frequency technology, operating at both 5 kHz and 15 kHz. This capability enables the detector to achieve greater penetration into the ground, providing the ability to locate deeper targets that many other detectors might miss. This is especially useful in areas with high mineralization where standard detectors may struggle.

Ergonomics also play a crucial role in the design of the CZ-3D. The device features a lightweight construction that ensures comfortable usage over extended periods. The adjustable shaft and user-friendly control layout allow for easy customization to suit individual preferences. Users can conveniently access settings such as sensitivity and discrimination levels, enhancing the overall user experience.

Water-resistant components make the CZ-3D suitable for various hunting environments, allowing operations in wet or humid conditions. This versatility broadens the scope of potential searching locations, from beaches and parks to rivers and fields.

In summary, the Fisher CZ-3D is distinguished by its powerful detection capabilities, advanced discrimination features, dual-frequency technology, and ergonomic design. For serious treasure hunters and coin collectors, the CZ-3D represents a dependable tool that combines innovation with practicality, making it a preferred choice for those aiming to uncover hidden treasures beneath the earth.
Top Page Image Contents