Dixon 44 / 968999538, 44 / 968999611, 44 / 968999547 Deck belt removal, Deck belt installation

Page 42

MAINTENANCE

Deck belt removal

1.Park on a level surface. Apply parking brake.

2.Lower the deck into the lowest cutting position.

3.Remove bolts from belt shields and remove shields.

4.Remove any dirt or grass that may have accumulated around the cutter housings and entire deck surface.

5.Carefully roll the belt over the top of the cutter housing pulleys and remove belt.

Deck belt installation

NOTE: For ease in installing the deck belt, refer to

2

1

the routing decal on bottom of seat.

1. Shield bolts

8050-773

1.

Wrap the deck belt around the electric clutch

 

pulley that is located on the engine shaft.

2.

Route the belt forward between the EZT (E-

 

Series Zeroturn Transaxles) and up onto the

 

deck.

3.

Place belt around spring loaded idler pulley.

4.

Wrap the belt around the stationary idler

 

pulley and around the mandrel housings.

5.

Push inward on the idler arm and carefully

 

route belt over stationary idler pulley. Once

 

belt is properly routed, slowly release idler

 

arm to tension belt.

6.

Double check belt routing to make sure it

 

matches the routing decal, and the belt does

 

not have any twist. Correct as needed.

7.

Adjust tension with deck eyebolt.

8.

Replace belt shields on both mandrel

 

housings and secure with fasteners.

2. Belt shields Removing deck belt

1

2

1. Clutch pulley

2. Deck belt

8050-773

Belt routing, deck belt

English-42

Image 42
Contents Speedztr Page Table of Contents Introduction Good Service Manufacturing NumberSymbols and Decals Important InformationRemove key before Safety Safety InstructionsGeneral Operation Never take passengers Personal Safety Equipment Slope OperationChildren Maintenance Safe Handling of GasolineGeneral Maintenance Risk of sparking Transport Customer responsibilities Controls ControlsMotion Control Levers TrackingSeat adjustment lever Unlocking TransmissionRefueling Ignition Switch Choke ControlThrottle Control Blade switch Circuit breakerParking Brake Mower Deck Cut Height Lift Lever Training OperationOperation To move forward and backwardBefore Starting Starting the EngineSteering controls in the outward, locked neutral position USE Full Throttle When Mowing To start an engine with a weak battery To attach jumper cablesTo remove cables, reverse order Running Operating on hills Mowing Tips Stopping the Engine Moving by Hand Unlocking TransmissionMaintenance Maintenance ScheduleMaintenance Before After 50 100 Battery To clean battery and terminalsReplacing battery Checking the Safety System Ignition SystemChecking and Adjusting the Throttle Cable Checking and Adjusting the Choke CableChecking the Engine’s Cooling Air Intake Replacing the Air Filter Replacing the Fuel Filter Checking the Fuel Pump’s Air FilterChecking the V-belts Checking Tire PressuresChecking the Parking Brake Deck beltDeck belt installation Deck belt removalChecking the Blades Belt installationPump Belt To replace EZT E-Series Zeroturn Transaxle beltBlade replacement Front-to-back adjustment Adjusting the Mower DeckSide-to-side adjustment To level deckTo adjust anti-scalp rollers Cleaning and WashingTo adjust parking brake HardwareTracking adjustment Mower is tracking to the rightMower is tracking to the left Lubrication Lubrication ScheduleChange transaxles transmission filters Front Wheel Bearings Lubricating the CablesFront Wheel Mount Deck spindleDeck outer spindle Engine Oil Changing the Engine OilChecking the Oil Level Changing the Engine Oil Filter Filter Top Port Plug Filter Guard Screws Purging Procedures Trouble Shooting Guide Problem CauseEnglish-57 English-58 Service StorageWinter Storage Wiring Diagrams Technical Data ZTR 44 ZTR 36 EngineTransmission Overall dimensions ZTR 44 ZTR 36 EquipmentProductivity Technical Data ZTR 36 ZTR 44 EngineZTR 36 ZTR 44 Equipment ZTR 42 Engine ZTR 42 Equipment ZTR 44 Engine ZTR 44 Equipment Torque Specifications Conformity Certificates Conformity CertificatesService Journal Action Date, mtr reading, stamp, signAfter the First 5-8 Hours Hour Service Service Journal Service Journal Service Journal At Least Once Each Year Service Journal Page Part No 131911 Rir 07/27/07