Dixon 44 / 968999547, 44 / 968999538 manual Deck outer spindle, Engine Oil Changing the Engine Oil

Page 51

LUBRICATION

Deck outer spindle

Lubricate using a grease gun, one zerk, each side 2- 3 strokes.

Use only good quality bearing grease.

Engine Oil

Changing the Engine Oil

The engine oil should be changed for the first time after 5-8 hours of operation. Thereafter, it should be changed every 50 hours.

WARNING!

Engine oil can be very hot if it is drained directly after stopping the engine. Allow the engine to cool somewhat first.

1.Place the machine on a flat surface.

2.Place a container under the engine where the hose from the oil drain valve exits.

3.Remove the dipstick and open the drain valve.

4.Allow the oil to run out into the container.

5.Then close the oil drain valve.

6.Replace the oil filter if necessary.

7.Fill with new engine oil in accordance with Checking the Oil Level.

8.Start the engine. Run it for a few seconds. Stop and re-check the oil level.

Deck outer spindle	8011-733

IMPORTANT INFORMATION

Used engine oil is a health hazard and must not be disposed of on the ground or in nature; it should always be disposed of at a workshop or appropriate disposal location.

Avoid skin contact; wash with soap and water in case of spills.

8011-730

Oil drain valve

English-51

Image 51

Contents Speedztr Page Table of Contents Introduction Manufacturing Number Good ServiceImportant Information Symbols and DecalsRemove key before Safety Safety InstructionsGeneral Operation Never take passengers Slope Operation Personal Safety EquipmentChildren Safe Handling of Gasoline MaintenanceGeneral Maintenance Risk of sparking Transport Customer responsibilities Controls ControlsTracking Motion Control LeversUnlocking Transmission Seat adjustment leverRefueling Ignition Switch Choke ControlThrottle Control Blade switch Circuit breakerParking Brake Mower Deck Cut Height Lift Lever To move forward and backward OperationOperation TrainingStarting the Engine Before StartingSteering controls in the outward, locked neutral position USE Full Throttle When Mowing To start an engine with a weak battery To attach jumper cablesTo remove cables, reverse order Running Operating on hills Mowing Tips Stopping the Engine Unlocking Transmission Moving by HandMaintenance Maintenance ScheduleMaintenance Before After 50 100 Battery To clean battery and terminalsReplacing battery Ignition System Checking the Safety SystemChecking and Adjusting the Throttle Cable Checking and Adjusting the Choke CableChecking the Engine’s Cooling Air Intake Replacing the Air Filter Checking the Fuel Pump’s Air Filter Replacing the Fuel FilterDeck belt Checking Tire PressuresChecking the Parking Brake Checking the V-beltsDeck belt removal Deck belt installationTo replace EZT E-Series Zeroturn Transaxle belt Belt installationPump Belt Checking the BladesBlade replacement To level deck Adjusting the Mower DeckSide-to-side adjustment Front-to-back adjustmentCleaning and Washing To adjust anti-scalp rollersHardware To adjust parking brakeTracking adjustment Mower is tracking to the rightMower is tracking to the left Lubrication Lubrication ScheduleChange transaxles transmission filters Deck spindle Lubricating the CablesFront Wheel Mount Front Wheel BearingsEngine Oil Changing the Engine Oil Deck outer spindleChecking the Oil Level Changing the Engine Oil Filter Filter Top Port Plug Filter Guard Screws Purging Procedures Problem Cause Trouble Shooting GuideEnglish-57 English-58 Service StorageWinter Storage Wiring Diagrams Technical Data ZTR 44 ZTR 36 EngineTransmission Overall dimensions ZTR 44 ZTR 36 EquipmentProductivity ZTR 36 ZTR 44 Engine Technical DataZTR 36 ZTR 44 Equipment ZTR 42 Engine ZTR 42 Equipment ZTR 44 Engine ZTR 44 Equipment Torque Specifications Conformity Certificates Conformity CertificatesAction Date, mtr reading, stamp, sign Service JournalAfter the First 5-8 Hours Hour Service Service Journal Service Journal Service Journal At Least Once Each Year Service Journal Page Part No 131911 Rir 07/27/07