Country Home Products FIELD and BRUSH MOWER operating instructions Procedure Before Each Every

Page 25

Chapter 5: Maintaining the DRALL-TERRAINFIELD and BRUSH MOWER

Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer's owner's manual for maintenance procedures. Service intervals listed in the checklist below supercede those listed in the engine manufacturer's owner's manual.

WARNING! Some of the following procedures require access to the underside of the machine. If you need to tip the machine back or on its side (with the discharge chute facing up), you must first disconnect the spark plug wire(s), drain the oil and gas, and remove the air filters.

Regular Maintenance Check List

Note: Service intervals shown are considered maximum under normal operating conditions. Increase frequencies under extremely dirty or dusty conditions.

Procedure

Before Each

Every 25

Every 100

Use

Hours

Hours

 

Check Operator Presence Switch

 

 

 

 

 

 

Check Engine Oil Level

 

 

Check General Equipment Condition

 

 

Check Blade for Sharpness

 

 

Lubricate Grease Fittings

 

 

Check Tire Pressure

 

 

Clean Air Filter & Precleaner*

 

 

Change Engine Oil & Filter*

1st time 5 hours

 

Check Parking Brake Adjustment

 

 

Clean Engine Exterior & Cooling Fins

 

 

Check All Belt Tensions & Condition

 

 

Lubricate Chain

 

 

Replace Spark Plug(s)

 

 

Replace Air Filter & Precleaner

 

 

Check cable connections

 

 

*The engine on your DR® may not have a precleaner or oil filter.

DRALL-TERRAINFIELD and BRUSH MOWER Safety & Operating Instructions

21

Image 25
Contents DR ALL-TERRAIN Brush Mower Table of Contents Page About This Manual Introducing the DR ALL-TERRAINFIELD and Brush MowerConventions used in this manual Safety Information Labels Safety ConsiderationsPreparing to Use the DR ALL-TERRAINFIELD and Brush Mower Page Operating the Machine Safely Protecting YourselfSafety with Gasoline-Powered Machines Fine Print Page Setting Up Your DR ALL-TERRAINFIELD and Brush Mower DR ALL-TERRAINFIELD and Brush Mower Controls and Features Tools & Supplies Needed Unpacking the MowerInstall Collar and Pin Install Belt Belt Tension Lever To Install the Brush DeckConnect Battery Wire Connecting the Battery Wire Electric-Starting Models OnlyCheck the Tire Pressure Adding Oil and GasolineApproximate Engine Oil Required w/ Oil Filter Before Starting the Engine Operating Your DR ALL-TERRAINFIELD and Brush MowerElectric-Starting Manual-StartingEngaging the Blade Engaging the Wheel DriveStopping the Blade Obstacle Tips Stopping the Engine If the machine gets hung up SlopesReverse Cutting Brush & SaplingsCutting in Wet & Heavy Growth Page Procedure Before Each Every Charging the Battery Battery Care For Electric-Starting Models OnlyLubrication Spindle Grease Fitting Belt Idler Arm Grease Fitting Grease FittingsRemove Chain Cover Lubricate Chain To Replace the Blade Belt Removing and Replacing the BeltsBelt Tension Lever Belt Removed Remove Pin & Collar To Replace the Drive Belt Tools NeededLoosen Bolt and Slide Back Remove Belt Guides Spring Clutch Bracket Remove NutsThread and washer Removing and Replacing the BladeWheel Clutch Adjustment Adjusting the Wheel ClutchRemove the Chain Cover Remove Tensioner Spring Removing and Replacing the Drive ChainBlade Engagement Cable Adjustment Adjusting the Blade Engagement CableTool Needed Tool Needed Adjust Parking Brake Adjusting the Parking BrakeRemoving the Wheels Removing or Changing the Deck TransmissionBelt Removed Belt Tension Lever Remove Pin & Collar End of Season & Storage Troubleshooting Table Troubleshooting and WarrantyStart, call 1800 DR-OWNER 376-9637 for Owner 376-9637 for assistance ⇒ Call 1800 DR-OWNER 376-9637 for assistance Page Page Year Limited Warranty Terms and Conditions Daily Checklist for the DR Field and Brush Mower