Bush Hog 2297 manual Transporting Safety Instructions and Practices

Page 16
(SL-21)
(SL-04)
(SG-19)

SAFETY

SAFETY

Transporting Safety Instructions and Practices

Transport only at speeds where you can maintain control of the equipment. Serious accidents and injuries can result from operating this equipment at high speeds. Understand the Tractor and Implement and

how it handles before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condition and operate properly.

Before transporting the Tractor and Implement, determine the proper transport speeds for you and the equipment. Make sure you abide by the following rules:

Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly to determine the stopping characteristics of the Tractor and Implement. As you increase the speed of the Tractor the stopping distance increases. Determine the maximum transport speed not to exceed 20 mph (30 kph) for transporting this equipment.

Test the equipment at a slow speed in turns. Increase the speed through the turn only after you determine that the equipment can be operated at a higher speed. Use extreme care and reduce your speed when turning sharply to prevent the tractor and implement from turning over. Determine the maximum turning speed for you and this equipment before operating on roads or uneven ground.

Only transport the Tractor and Implement at the speeds which allow you to properly control the equipment.

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes or worn tires. When operating down a hill or on wet or rain slick roads, the braking distance increases: use extreme care and reduce your speed. When operating in traffic always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you and watch out for the other guy.

Before transporting the tractor and Loader engage the loader valve travel lock to prevent inadvertent contact with the joystick controller causing sudden dropping of the loader and attachment. If the loader attachment, such as a bucket, were to drop suddenly and hit the ground while transporting, the tractor could stop immediately resulting in the operator hitting the steering wheel or flying our of the operator’s seat. Serious injury could result.

Do not raise the loader on a hillside. Do not transport across a slope with a raised loader. When the loader is raised, the center of gravity of the tractor and loader is raised increasing the potential for the tractor to tip over. Tractor wheel contact with any wash out, drop off or the ground obstruction with a raised loader could result in the tractor tipping over and causing serious bodily injury.

2297 01/11

Safety Section 1-12

© 2011 Alamo Group Inc.

Image 16
Contents 2297 Warranty Information To the Owner/Operator/DealerTable of Contents Maintenance Section Safety Section Safety General Safety Instructions and Practices2297 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 2297 01/11 Safety Section Safety SL-33 SPU-2 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesParts Information Decal Location Logo ModelInstruct ReflctrDecal Description Model NameD469 2297 01/11 Safety Section Safety Safety Federal Laws and Regulations Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Assembly Dismounting Loader and Mounting Loader to Tractor2297 01/11 Assembly Section Proper Ballasting and Wheel Spacing Dismounting Loader Mounting LoaderAttaching Pin on Bucket Assembling Quick Attach Device Installing Quick Attach Device When Connecting an Attachment to the Loader Quick Hitch Assembly Operation Section Operation Standard Equipment and Specifications GPMOperator Requirements Operation Tractor Requirements Personal Protective Equipment PPETractor Lighting and SMV Emblem Rops and Seat BeltTractor Ballast Getting On and Off the Tractor Boarding the TractorDismounting the Tractor Starting the Tractor Pre-Operation Inspection and Service Tractor Pre-Operation Inspection/Service Loader Pre-Operation Inspection/ServiceMount Assembly Hydraulic Line Inspection Loader Boom AssemblyBucket Inspection Do not Operate an Unsafe Tractor or Implement Do not Operate an Unsafe Tractor or Front END Loader Driving the Tractor and Loader Operating the Tractor and Loader Driving the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Operating the Loader Filling the BucketLifting the Load Carrying the Load Dumping the Bucket Lowering the BucketOperating with Float Control Loading from a BankOperation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Optional Attachment Loader Storage Shutting Down the ImplementTransporting the Tractor and Implement Operation Transporting on Public Roadways Hauling the Tractor and Implement Troubleshooting Guide Trouble Possible Cause Possible RemedyProblem Possible Cause Remedy Maintenance Section Maintenance 2297 01/11 Maintenance Section Lubrication Schedule Daily Maintenance Cylinder Service Lift and Bucket Cylinder DisassemblyLift and Bucket Cylinder Reassembly StorageMaintenance Proper Torque for Fasteners Maintenance Maintenance Limited Warranty Required of the Owner Required of the OperatorSOM-01/11 Printed U.S.A

2297 specifications

The Bush Hog 2297 is a robust, versatile rotary cutter that has earned a reputation for its durability and efficiency in various land maintenance tasks. Designed for both commercial and agricultural use, this mower is particularly well-suited for cutting tall grasses, weeds, and brush, making it an ideal choice for property maintenance, farming, and clearing overgrown areas.

One of the primary features of the Bush Hog 2297 is its heavy-duty construction. The cutter is built with a robust steel frame and a heavy-duty deck that provides stability and strength, allowing it to withstand the rigors of tough mowing conditions. The quality of materials used in its construction ensures a long lifespan, making it a worthwhile investment for users seeking reliability.

The 2297 is equipped with a powerful 97-inch cutting width, which enables operators to cover large areas quickly and efficiently. This feature significantly reduces mowing time compared to smaller models, making it an ideal choice for users needing to manage large properties or agricultural land. Its cutting height can be easily adjusted, allowing for a customizable mowing experience tailored to different terrains and vegetation types.

In terms of technology, the Bush Hog 2297 features a patented swing-hitch design that enables the cutter to follow the contours of the ground. This design provides an even cut, regardless of the terrain, ensuring that users achieve a professional-looking finish. Additionally, the mower incorporates heavy-duty blades that are designed for maximum cutting efficiency, capable of handling even the toughest brush and vegetation.

Safety is a priority with the Bush Hog 2297, which includes features like an integrated safety chain and a reliable gearbox that protects against stall and overload situations. Operators can work with peace of mind, knowing that the equipment has built-in safeguards to prevent accidents and prolong the life of the mower.

The Bush Hog 2297 is compatible with a range of tractors, making it a versatile addition to any farming or landscaping toolkit. With its combination of durability, powerful performance, and innovative design, the Bush Hog 2297 stands out as a top choice for those seeking a high-quality rotary cutter that delivers consistent results in diverse mowing conditions. Whether you’re managing a farm, maintaining a large property, or clearing brush, the Bush Hog 2297 is the tool you can rely on to get the job done effectively.