Bush Hog 2297 manual Dismounting Loader, Mounting Loader

Page 37

ASSEMBLY

Dismounting Loader and Mounting Loader to Tractor

Dismounting Loader

1.Locate tractor and loader on firm level ground.

2.Level and lower bucket to ground. Engage tractor brakes and shut off tractor engine. Move lift control lever back and forth several times to relieve pressure in lift cylinders.

3.Remove 5/8 lock nuts and washers which clamp hinges closed around mid mounting tubes on tractor.

4.Unhook and remove rubber strap which secures hoses to front of side frame.

5.Start tractor engine and release tractor brakes. Activate lift control lever to raise side frame up off midmounting assembly. Continue rotating loader side frames off midmounting tubes. Slowly back tractor out of loader while rotating loader side frames. Allow loader to roll off front mounting bracket until lift cylinders are fully extended and yoke is resting on ground. Engage tractor brakes and shut off tractor engine.

6.Move lift and bucket control levers back and forth several times to relieve pressure on lift and bucket cylinders. Disconnect quick couplers between loader and tractor. Hang hoses over loader side frame upright for storage. Make sure male quick couplers will not become contaminated during storage.

7.Fasten bolts, washers and nuts onto hinge for storage.

NOTE: Loader should be stored in a dry place. If loader is being stored for an extended period (one month or more), a coat of grease should be applied to the cylinder shafts to prevent rusting.

Mounting Loader

Mounting is basically reverse of dismounting.

1.Slowly drive tractor up to loader until hoses will reach from loader to tractor. Engage tractor brakes and shut off tractor engine.

2.Make sure quick couplers are clean and connect between tractor and loader, matching color coded bands.

3.Remove bolts, nuts and washers from hinge.

4.Start tractor engine and release tractor brakes. Slowly drive tractor ahead until front mounting brackets are directly under loader catch flats. Activate lift control lever so that catch flats hook securely on front mounting bracket tubes. Continue driving loader forward while rolling the loader on the front mounting bracket tubes until side frame uprights are fully resting on midmounting assembly. Engage tractor brakes and shut off engine.

2297 01/11

Assembly Section 3-5

© 2011 Alamo Group Inc.

ASSEMBLY

Image 37
Contents 2297 To the Owner/Operator/Dealer Warranty InformationTable of Contents Maintenance Section Safety Section General Safety Instructions and Practices Safety2297 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 2297 01/11 Safety Section Safety SL-33 SPU-2 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices Safety Concluding Safety Instructions and Practices Storage and Parking Safety Instructions and PracticesParts Information Decal Location Model LogoInstruct ReflctrModel Name Decal DescriptionD469 2297 01/11 Safety Section Safety Safety Federal Laws and Regulations Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Dismounting Loader and Mounting Loader to Tractor Assembly2297 01/11 Assembly Section Proper Ballasting and Wheel Spacing Mounting Loader Dismounting LoaderAttaching Pin on Bucket Assembling Quick Attach Device Installing Quick Attach Device When Connecting an Attachment to the Loader Quick Hitch Assembly Operation Section Operation GPM Standard Equipment and SpecificationsOperator Requirements Operation Personal Protective Equipment PPE Tractor RequirementsTractor Lighting and SMV Emblem Rops and Seat BeltTractor Ballast Boarding the Tractor Getting On and Off the TractorDismounting the Tractor Starting the Tractor Pre-Operation Inspection and Service Loader Pre-Operation Inspection/Service Tractor Pre-Operation Inspection/ServiceMount Assembly Hydraulic Line Inspection Loader Boom AssemblyBucket Inspection Do not Operate an Unsafe Tractor or Implement Do not Operate an Unsafe Tractor or Front END Loader Driving the Tractor and Loader Driving the Tractor and Loader Operating the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Filling the Bucket Operating the LoaderLifting the Load Carrying the Load Lowering the Bucket Dumping the BucketLoading from a Bank Operating with Float ControlOperation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Optional Attachment Shutting Down the Implement Loader StorageTransporting the Tractor and Implement Operation Transporting on Public Roadways Hauling the Tractor and Implement Trouble Possible Cause Possible Remedy Troubleshooting GuideProblem Possible Cause Remedy Maintenance Section Maintenance 2297 01/11 Maintenance Section Lubrication Schedule Daily Maintenance Lift and Bucket Cylinder Disassembly Cylinder ServiceStorage Lift and Bucket Cylinder ReassemblyMaintenance Proper Torque for Fasteners Maintenance Maintenance Limited Warranty Required of the Operator Required of the OwnerSOM-01/11 Printed U.S.A

2297 specifications

The Bush Hog 2297 is a robust, versatile rotary cutter that has earned a reputation for its durability and efficiency in various land maintenance tasks. Designed for both commercial and agricultural use, this mower is particularly well-suited for cutting tall grasses, weeds, and brush, making it an ideal choice for property maintenance, farming, and clearing overgrown areas.

One of the primary features of the Bush Hog 2297 is its heavy-duty construction. The cutter is built with a robust steel frame and a heavy-duty deck that provides stability and strength, allowing it to withstand the rigors of tough mowing conditions. The quality of materials used in its construction ensures a long lifespan, making it a worthwhile investment for users seeking reliability.

The 2297 is equipped with a powerful 97-inch cutting width, which enables operators to cover large areas quickly and efficiently. This feature significantly reduces mowing time compared to smaller models, making it an ideal choice for users needing to manage large properties or agricultural land. Its cutting height can be easily adjusted, allowing for a customizable mowing experience tailored to different terrains and vegetation types.

In terms of technology, the Bush Hog 2297 features a patented swing-hitch design that enables the cutter to follow the contours of the ground. This design provides an even cut, regardless of the terrain, ensuring that users achieve a professional-looking finish. Additionally, the mower incorporates heavy-duty blades that are designed for maximum cutting efficiency, capable of handling even the toughest brush and vegetation.

Safety is a priority with the Bush Hog 2297, which includes features like an integrated safety chain and a reliable gearbox that protects against stall and overload situations. Operators can work with peace of mind, knowing that the equipment has built-in safeguards to prevent accidents and prolong the life of the mower.

The Bush Hog 2297 is compatible with a range of tractors, making it a versatile addition to any farming or landscaping toolkit. With its combination of durability, powerful performance, and innovative design, the Bush Hog 2297 stands out as a top choice for those seeking a high-quality rotary cutter that delivers consistent results in diverse mowing conditions. Whether you’re managing a farm, maintaining a large property, or clearing brush, the Bush Hog 2297 is the tool you can rely on to get the job done effectively.