Bush Hog manual 2297 01/11 Assembly Section

Page 35
(SL-32)
(SL-11)
(SL-15)

ASSEMBLY

Do not use an attachment that is not securely attached to the quick hitch, The attachment could fall resulting in severe crushing injuries or death to the operator or bystanders.

•Rotate both hitch pin levers down to the locked position. You should feel a firm resistance when locking the levers down. The pins must extend through the slots in the bottom of the attachment bracket.

•Examine the fit between the quick hitch and the bottom of the attachment bracket. The pins must extend through the slots in the bottom of the attachment bracket. The tapered side of each pin must be firmly wedged against the surface of the slot on the bottom of the attachment bracket. The attachment bucket should fit snugly against the bottom of the quick hitch bracket. If there is a gap of more than 1/8” or if the pins are not firmly seated do not use the attachment. Contact your dealer before using the attachment.

•On level ground, tilt the attachment down 90° degrees and lower it to the ground. Lower the loader further to slightly raise the front of the tractor off the ground. Drive the tractor in reverse while the attachment is on the ground for 20-30 feet to ensure the attachment does not disconnect. If the attachment disconnects during this process, discontinue the use of the attachment and contact your dealer.

NEVER walk or work under or allow any person to be underneath a raised loader or attachment.

Only mount the loader on a tractor that is listed on the mounting instructions. Never mount on a tricycle steering front axle. Move the tractor front and rear wheels to the widest spacing and add the recommended rear tractor ballast to prevent tractor tip over. Keep the tractor tires properly inflated. Maintain at least 25% of the total Tractor and Loader weight including the maximum load in the bucket or attachment on the rear axle. Always wear your seatbelt and make sure the ROPS structure is fully deployed to prevent serious injury or death from the tractor tipping over.

Make sure all air is purged from the hydraulic system before using the loader. Air in the system can cause the loader to respond sluggishly or with unexpected movement. The air can be purged from the cylinder lines by fully cycling the cylinders several times from the fully closed to fully open position. Sudden or unexpected movement or dropping of the loader and attachment could result in serious injury.

ASSEMBLY

2297 01/11

Assembly Section 3-3

© 2011 Alamo Group Inc.

Page 34 Page 36
Image 35
Page 34 Page 36
Contents 2297 To the Owner/Operator/Dealer Warranty InformationTable of Contents Maintenance Section Safety Section General Safety Instructions and Practices Safety2297 01/11 Safety Section Operator Safety Instructions and Practices Equipment Operation Safety Instructions and Practices SG-36 2297 01/11 Safety Section Safety SL-33 SPU-2 Safety Transporting Safety Instructions and Practices Maintenance and Service Safety Instructions and Practices Safety Parts Information Storage and Parking Safety Instructions and PracticesConcluding Safety Instructions and Practices Decal Location Reflctr LogoModel InstructModel Name Decal DescriptionD469 2297 01/11 Safety Section Safety Safety Federal Laws and Regulations Introduction Section Introduction Introduction Introduction Before Operating this Machine Page Assembly and Connecting the Loader Section Dismounting Loader and Mounting Loader to Tractor Assembly2297 01/11 Assembly Section Proper Ballasting and Wheel Spacing Mounting Loader Dismounting LoaderAttaching Pin on Bucket Assembling Quick Attach Device Installing Quick Attach Device When Connecting an Attachment to the Loader Quick Hitch Assembly Operation Section Operation GPM Standard Equipment and SpecificationsOperator Requirements Operation Personal Protective Equipment PPE Tractor RequirementsTractor Ballast Rops and Seat BeltTractor Lighting and SMV Emblem Boarding the Tractor Getting On and Off the TractorDismounting the Tractor Starting the Tractor Pre-Operation Inspection and Service Loader Pre-Operation Inspection/Service Tractor Pre-Operation Inspection/ServiceMount Assembly Bucket Inspection Loader Boom AssemblyHydraulic Line Inspection Do not Operate an Unsafe Tractor or Implement Do not Operate an Unsafe Tractor or Front END Loader Driving the Tractor and Loader Driving the Tractor and Loader Operating the Tractor and LoaderSG-36 Operation Operation SL-33 Operation Filling the Bucket Operating the LoaderLifting the Load Carrying the Load Lowering the Bucket Dumping the BucketLoading from a Bank Operating with Float ControlOperation Peeling and Scraping Loading LOW Trucks or Spreaders from a Pile Backfilling Operation Handling Large Heavy Objects Operating Bale Spear Optional Attachment Shutting Down the Implement Loader StorageTransporting the Tractor and Implement Operation Transporting on Public Roadways Hauling the Tractor and Implement Trouble Possible Cause Possible Remedy Troubleshooting GuideProblem Possible Cause Remedy Maintenance Section Maintenance 2297 01/11 Maintenance Section Lubrication Schedule Daily Maintenance Lift and Bucket Cylinder Disassembly Cylinder ServiceStorage Lift and Bucket Cylinder ReassemblyMaintenance Proper Torque for Fasteners Maintenance Maintenance Limited Warranty Required of the Operator Required of the OwnerSOM-01/11 Printed U.S.A

2297 specifications

The Bush Hog 2297 is a robust, versatile rotary cutter that has earned a reputation for its durability and efficiency in various land maintenance tasks. Designed for both commercial and agricultural use, this mower is particularly well-suited for cutting tall grasses, weeds, and brush, making it an ideal choice for property maintenance, farming, and clearing overgrown areas.

One of the primary features of the Bush Hog 2297 is its heavy-duty construction. The cutter is built with a robust steel frame and a heavy-duty deck that provides stability and strength, allowing it to withstand the rigors of tough mowing conditions. The quality of materials used in its construction ensures a long lifespan, making it a worthwhile investment for users seeking reliability.

The 2297 is equipped with a powerful 97-inch cutting width, which enables operators to cover large areas quickly and efficiently. This feature significantly reduces mowing time compared to smaller models, making it an ideal choice for users needing to manage large properties or agricultural land. Its cutting height can be easily adjusted, allowing for a customizable mowing experience tailored to different terrains and vegetation types.

In terms of technology, the Bush Hog 2297 features a patented swing-hitch design that enables the cutter to follow the contours of the ground. This design provides an even cut, regardless of the terrain, ensuring that users achieve a professional-looking finish. Additionally, the mower incorporates heavy-duty blades that are designed for maximum cutting efficiency, capable of handling even the toughest brush and vegetation.

Safety is a priority with the Bush Hog 2297, which includes features like an integrated safety chain and a reliable gearbox that protects against stall and overload situations. Operators can work with peace of mind, knowing that the equipment has built-in safeguards to prevent accidents and prolong the life of the mower.

The Bush Hog 2297 is compatible with a range of tractors, making it a versatile addition to any farming or landscaping toolkit. With its combination of durability, powerful performance, and innovative design, the Bush Hog 2297 stands out as a top choice for those seeking a high-quality rotary cutter that delivers consistent results in diverse mowing conditions. Whether you’re managing a farm, maintaining a large property, or clearing brush, the Bush Hog 2297 is the tool you can rely on to get the job done effectively.
Top Page Image Contents