Briggs & Stratton RIDER 13 BIO, RIDER 11 BIO, RIDER 16 manual Reparation instructions

Page 43

Reparation instructions

4. Remove the transmission cover.

7. Lift off the linkage and pull out the wire.

5

Follow the hydrostatic transmission wire backwards towards the transmission and cut off the cable ties round the wire.

6

8

Lift out the transmission wire with the linkage attached.

9

Remove the lock spring at the transmission wire’s rear linkage. Release the clamp holding the wire’s casing.

Unscrew both ball joints from the hydrostatic transmission wire.

10

Remove the entire hydrostatic transmission wire.

English – 41

Image 43

Contents Rider 11, Rider Rider 11 Bio, Rider 13 Bio, Rider Svenska Workshop manual Rider 11, Rider Rider 11 Bio, Rider 13 Bio ContentsGeneral instructions Safety regulationsSpecial instructions Special tools Tightening moments Technical dataPlay Mowing deck BioClip Combi Mowing deck Rear ejector Side ejector BioControl points Pre-delivery service Delivery and dealer serviceAfter first 5 hours At least once a season Dealer service Hours serviceHours Maintenance scheduleMaintenance interval MaintenanceParts enclosed in packaging, Rider Delivery measuresTo our dealer Packaging and unpackingMeasures for contact with acid BatteryTow plate Steering wheelCheck the oil level in the engine Wheels Checking the oil level in the transmissionTest running Speed regulator AdministrationGeneral Design and functionSerial number Engine Steering Mowing deck DrivingCombi 1030 mm Combi 1120 mm Mowing height manoeuvring Removing engine Reparation instructionsHold the bolts so that the poles are not put under strain Reparation instructions Replacing engine Reparation instructions Fitting Fuel tank RemovalChanging the oil Checking and adjusting steering wiresRemoval/installation of steering axle Replacing steering wiresRemoval/installation of wire wheel Badly adjusted brake can lead to reduced braking capacity Checking and adjusting brake wireRider 13 and Rider Checking and adjusting freewheel clutch Rider Checking and adjusting gear control RiderReplacing articulated steering bearing Checking and adjusting throttle controlReparation instructions Replacing bushings Removal of swing axleRider 13 Installation of swing axle Removal/installation of gear box Replacing hydrostatic transmission axle sealing collars Sealing collar replacement input axleSealing collar replacement outgoing axles Removal of hydrostatic transmission wire Replacing hydrostatic transmission wireReparation instructions Refitting hydrostatic transmission wire ~80 Bleeding the hydrostatic transmission oil system Adjustment of transmission neutral positionOil change Transmission maintenanceChanging oil Rider 13 and Rider Removing the beltRider 11, Rider 13 H, Rider 16 H och Rider 14 Pro Checking and adjusting mower deck parallelism Checking and adjusting mower deck ground pressureAdjusting Rider 11 and Rider 13 H Adjusting Rider 11 Bio and Rider 13 Bio Adjusting cutting height Adjusting cutting height areaRemoving the cutting unit To leave the service position Rear and side ejectors Dismantling the cutting unitReplacing the cutting unit’s belts Belt replacement on BioClip 103 and CombiBelt replacement on BioClip Removal of blades with bearings Replacing the break-pin BioClip 90, 103 and CombiImportant Information Grinding and balancing of blades When working with the blades, use protective glovesElectrical system Circuit diagram RiderCircuit diagram Rider 13 and Rider 13 Bio Pos Utf Inspecting the safety system Microswitch Mowing Deck Microswitch Seat Microswitch Neutral PositionIgnition and Starter Lock Main fuse Engine will not Start Engine Starts but does not RUN Satisfactorily Page Page Page Svenska Svenska Svenska ´z+H.T¶6w¨ Svenska 114 01 ´z+H.T¶6w¨ 2002W51Also See