Briggs & Stratton RIDER 13 Delivery and dealer service, Pre-delivery service, After first 5 hours

Page 9

Delivery and dealer service

Pre-delivery service

1.Top up battery with acid and recharge for four hours.

2.Fit the steering wheel, tow plate, and where appropriate other parts.

3.Adjust cutting unit:

Adjust lift springs (effective weight of cutting unit should be

12–15 kg (26,5-33 lb), or set to maximum lift if brush is to be fitted). (Only applies to BioClip and Combi.)

Adjust cutting unit so that rear edge is about 2–4 mm (1/8") higher than front edge.

Adjust cutting unit height setting so that cutting height limit is 5 mm (3/16") above the frame of the unit at the lowest cutting height.

4.Check that engine has correct amount of oil.

5.Check that the right amount of oil is in the transmission. (Not Rider 11)

6.Check and adjust tyre pressure (60 kPa/0,6 bar/8,5 PSI).

7.Connect battery.

8.Fill with fuel and start engine.

9.Check that machine does not move in neutral. (Not Rider 11)

10.Check:

Forward drive.

Reverse drive.

Operation of blades.

Seat safety switch.

Lift lever safety switch.

11.Check engine revs 2 900 - 3 100 rpm. Rider 16, 2003- model, 2 800-3 000 rpm.

12.Tell customer about:

Need and benefits of following the service schedule.

Need and benefits of having machine serviced every 300 hours.

The effects of maintenance on the machine’s second-hand value.

Applications for BioClip and Combi.

13. Complete proof of sale, etc.

After first 5 hours

1. Change engine oil.

English – 7

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Rider 11, Rider Rider 11 Bio, Rider 13 Bio, Rider Svenska Workshop manual Rider 11, Rider Rider 11 Bio, Rider 13 Bio ContentsSafety regulations General instructionsSpecial instructions Special tools Technical data Tightening momentsPlay Mowing deck BioClip Combi Mowing deck Rear ejector Side ejector BioControl points Delivery and dealer service Pre-delivery serviceAfter first 5 hours At least once a season Dealer service Hours serviceMaintenance interval Maintenance scheduleMaintenance HoursTo our dealer Delivery measuresPackaging and unpacking Parts enclosed in packaging, RiderMeasures for contact with acid BatterySteering wheel Tow plateCheck the oil level in the engine Wheels Checking the oil level in the transmissionTest running Speed regulator AdministrationGeneral Design and functionSerial number Engine Steering Mowing deck DrivingCombi 1030 mm Combi 1120 mm Mowing height manoeuvring Reparation instructions Removing engineHold the bolts so that the poles are not put under strain Reparation instructions Replacing engine Reparation instructions Fitting Fuel tank RemovalChanging the oil Checking and adjusting steering wiresRemoval/installation of steering axle Replacing steering wiresRemoval/installation of wire wheel Checking and adjusting brake wire Badly adjusted brake can lead to reduced braking capacityRider 13 and Rider Checking and adjusting freewheel clutch Rider Checking and adjusting gear control RiderReplacing articulated steering bearing Checking and adjusting throttle controlReparation instructions Removal of swing axle Replacing bushingsRider 13 Installation of swing axle Removal/installation of gear box Replacing hydrostatic transmission axle sealing collars Sealing collar replacement input axleSealing collar replacement outgoing axles Removal of hydrostatic transmission wire Replacing hydrostatic transmission wireReparation instructions Refitting hydrostatic transmission wire ~80 Bleeding the hydrostatic transmission oil system Adjustment of transmission neutral positionOil change Transmission maintenanceRemoving the belt Changing oil Rider 13 and RiderRider 11, Rider 13 H, Rider 16 H och Rider 14 Pro Checking and adjusting mower deck ground pressure Checking and adjusting mower deck parallelismAdjusting Rider 11 and Rider 13 H Adjusting Rider 11 Bio and Rider 13 Bio Adjusting cutting height Adjusting cutting height areaRemoving the cutting unit To leave the service position Rear and side ejectors Dismantling the cutting unitReplacing the cutting unit’s belts Belt replacement on BioClip 103 and CombiBelt replacement on BioClip Removal of blades with bearings Replacing the break-pin BioClip 90, 103 and CombiImportant Information Grinding and balancing of blades When working with the blades, use protective glovesElectrical system Circuit diagram RiderCircuit diagram Rider 13 and Rider 13 Bio Pos Utf Inspecting the safety system Microswitch Mowing Deck Microswitch Seat Microswitch Neutral PositionIgnition and Starter Lock Main fuse Engine will not Start Engine Starts but does not RUN Satisfactorily Page Page Page Svenska Svenska Svenska ´z+H.T¶6w¨ Svenska 114 01 ´z+H.T¶6w¨ 2002W51Also See

RIDER 13, RIDER 13 BIO, RIDER 16, RIDER 11 BIO, RIDER 11 specifications

Briggs & Stratton is a well-known name in the world of outdoor power equipment, and their RIDER series models, including RIDER 11, RIDER 16, RIDER 13, RIDER 11 BIO, and RIDER 13 BIO, exemplify innovation and efficiency in lawn care. Each model has distinct features tailored to meet diverse gardening needs and preferences.

The RIDER 11 is designed for those seeking a compact yet powerful riding mower. With a robust 11 HP engine and a cutting width of 28 inches, it maneuvers easily in tight spaces while still delivering efficient grass cutting. Its ergonomic design ensures comfort during extended use, and the mulching capability allows for clean lawn maintenance.

Next up, the RIDER 16 offers a higher power output with a 16 HP engine, making it ideal for larger lawns. The 33-inch cutting deck increases productivity, allowing users to cover more ground in less time. This model features a hydrostatic transmission, providing smooth and effortless speed control, enhancing the overall mowing experience.

The RIDER 13 stands as a versatile option, featuring a 13 HP engine and a 30-inch cutting deck. This model excels in ease of operation with its user-friendly controls, enabling even novice users to achieve professional results. The adjustable cutting height offers additional customization, allowing for precision mowing depending on the season and grass type.

For environmentally conscious users, the RIDER 11 BIO and RIDER 13 BIO models provide eco-friendliness without compromising performance. Equipped with bio-based components and a reduced carbon footprint, these models ensure a greener approach to lawn care. They retain the essential features of their counterparts, including efficient mowing performance and comfort while emphasizing reduced environmental impact.

Overall, the RIDER series by Briggs & Stratton embodies quality, versatility, and innovation. With robust engines, various cutting widths, and eco-friendly options, these riding mowers are tailored to meet the needs of every lawn care enthusiast. Whether you prioritize power, maneuverability, or sustainability, there’s a RIDER model that can help you maintain a beautifully manicured lawn with ease.
Top Page Image Contents