Briggs & Stratton RIDER 11 BIO, RIDER 16, RIDER 13 BIO manual Engine will not Start

Page 66

ENGINE WILL NOT START

Starter motor does not turn the engine

No spark from spark plug

Incorrect fuel supply

Discharged battery

No contact on starter relay

Starter motor and/or cable connection defective

Heavily burnt electrodes

Bad ignition cable connection

Spark plug short circuited

Defective ignition coil

Fuel tank empty

Fuel stop valve does not open

No fuel to the carburettor

No fuel from the carburettor (Spark plug dry)

Charge battery

Change battery

No current to relay

Relay defective

Change relay

Check connections

Change starter motor

Adjust electrode gap or replace spark plug

Change the spark plug cap

Replace the spark plug

Change the ignition coil

Fill with fuel

No current to the valve or the solenoid is defective

Channel from the fuel stop valve blocked

Fuel filter blocked

Tank ventilator blocked

Fuel pump defective

Fuel pipes blocked or pinched

Needles and diffuser jets blocked

Bad contact on battery poles

Blown fuse

Bad or no earth contact

Defective ignition switch

Microswitch on the cutting equipment’s lifting lever defective or in wrong position

Defective microswitch under seat

Microswitches by gear lever, hydraulic pedal defective or in wrong position (neutral pos)

Check cable connections or replace the valve

Clean the channel with compressed air

Change the filter.

Clean or replace the fuel cap

Broken pump diaphragm

Impulse channel blocked

Clean or replace the pipes

Clean the carburettor with compressed air

Clean and lubricate with copper paste

Change the fuse

Localise fault

Clean, lubricate with copper paste. Tighten the earth cable

Check cable connections or replace the switch

Check cable connections or replace the switch

Adjust the setting

Check cable connections or replace the switch

Check cable connections or replace the switch

Adjust the setting

Change the diaphragm

Clean the channel with compressed air

Page 65 Page 67
Image 66
Page 65 Page 67
Contents Rider 11, Rider Rider 11 Bio, Rider 13 Bio, Rider Svenska Rider 11, Rider Rider 11 Bio, Rider 13 Bio Contents Workshop manualSafety regulations General instructionsSpecial instructions Special tools Technical data Tightening momentsPlay Mowing deck Rear ejector Side ejector Bio Mowing deck BioClip CombiControl points Delivery and dealer service Pre-delivery serviceAfter first 5 hours Dealer service Hours service At least once a seasonMaintenance Maintenance scheduleMaintenance interval HoursPackaging and unpacking Delivery measuresTo our dealer Parts enclosed in packaging, RiderBattery Measures for contact with acidSteering wheel Tow plateCheck the oil level in the engine Checking the oil level in the transmission WheelsTest running Administration Speed regulatorDesign and function GeneralSerial number Engine Steering Driving Mowing deckCombi 1030 mm Combi 1120 mm Mowing height manoeuvring Reparation instructions Removing engineHold the bolts so that the poles are not put under strain Reparation instructions Replacing engine Reparation instructions Fuel tank Removal FittingChecking and adjusting steering wires Changing the oilReplacing steering wires Removal/installation of steering axleRemoval/installation of wire wheel Checking and adjusting brake wire Badly adjusted brake can lead to reduced braking capacityRider 13 and Rider Checking and adjusting gear control Rider Checking and adjusting freewheel clutch RiderChecking and adjusting throttle control Replacing articulated steering bearingReparation instructions Removal of swing axle Replacing bushingsRider 13 Installation of swing axle Removal/installation of gear box Sealing collar replacement input axle Replacing hydrostatic transmission axle sealing collarsSealing collar replacement outgoing axles Replacing hydrostatic transmission wire Removal of hydrostatic transmission wireReparation instructions Refitting hydrostatic transmission wire ~80 Adjustment of transmission neutral position Bleeding the hydrostatic transmission oil systemTransmission maintenance Oil changeRemoving the belt Changing oil Rider 13 and RiderRider 11, Rider 13 H, Rider 16 H och Rider 14 Pro Checking and adjusting mower deck ground pressure Checking and adjusting mower deck parallelismAdjusting Rider 11 and Rider 13 H Adjusting Rider 11 Bio and Rider 13 Bio Adjusting cutting height area Adjusting cutting heightRemoving the cutting unit To leave the service position Dismantling the cutting unit Rear and side ejectorsBelt replacement on BioClip 103 and Combi Replacing the cutting unit’s beltsBelt replacement on BioClip Replacing the break-pin BioClip 90, 103 and Combi Removal of blades with bearingsImportant Information When working with the blades, use protective gloves Grinding and balancing of bladesCircuit diagram Rider Electrical systemCircuit diagram Rider 13 and Rider 13 Bio Pos Utf Inspecting the safety system Microswitch Seat Microswitch Neutral Position Microswitch Mowing DeckIgnition and Starter Lock Main fuse Engine will not Start Engine Starts but does not RUN Satisfactorily Page Page Page Svenska Svenska Svenska ´z+H.T¶6w¨ Svenska ´z+H.T¶6w¨ 2002W51 114 01Also See

RIDER 13, RIDER 13 BIO, RIDER 16, RIDER 11 BIO, RIDER 11 specifications

Briggs & Stratton is a well-known name in the world of outdoor power equipment, and their RIDER series models, including RIDER 11, RIDER 16, RIDER 13, RIDER 11 BIO, and RIDER 13 BIO, exemplify innovation and efficiency in lawn care. Each model has distinct features tailored to meet diverse gardening needs and preferences.

The RIDER 11 is designed for those seeking a compact yet powerful riding mower. With a robust 11 HP engine and a cutting width of 28 inches, it maneuvers easily in tight spaces while still delivering efficient grass cutting. Its ergonomic design ensures comfort during extended use, and the mulching capability allows for clean lawn maintenance.

Next up, the RIDER 16 offers a higher power output with a 16 HP engine, making it ideal for larger lawns. The 33-inch cutting deck increases productivity, allowing users to cover more ground in less time. This model features a hydrostatic transmission, providing smooth and effortless speed control, enhancing the overall mowing experience.

The RIDER 13 stands as a versatile option, featuring a 13 HP engine and a 30-inch cutting deck. This model excels in ease of operation with its user-friendly controls, enabling even novice users to achieve professional results. The adjustable cutting height offers additional customization, allowing for precision mowing depending on the season and grass type.

For environmentally conscious users, the RIDER 11 BIO and RIDER 13 BIO models provide eco-friendliness without compromising performance. Equipped with bio-based components and a reduced carbon footprint, these models ensure a greener approach to lawn care. They retain the essential features of their counterparts, including efficient mowing performance and comfort while emphasizing reduced environmental impact.

Overall, the RIDER series by Briggs & Stratton embodies quality, versatility, and innovation. With robust engines, various cutting widths, and eco-friendly options, these riding mowers are tailored to meet the needs of every lawn care enthusiast. Whether you prioritize power, maneuverability, or sustainability, there’s a RIDER model that can help you maintain a beautifully manicured lawn with ease.
Top Page Image Contents