Bolens 247.77635 manual Starting Engine, Gasoline, Type of Fuel, Fuel Fill-up

Page 10

•Tighten the dipstick before removing it and check the oil fill level. See Figure 8.

Full

Figure 8

NOTE: Do not allow the dipstick to rub along the inside walls of the oil fill tube when removing it. Doing so may result in a false dipstick reading.

•Check oil level three times prior to starting engine to be certain you’ve gotten an accurate dipstick reading.

IMPORTANT: Running the engine with too little oil can result in permanent engine damage.

Gasoline

Type of Fuel

•Use clean, fresh, regular unleaded gasoline with a minimum of 85 octane. Fresh fuel prevents gum from forming in the fuel system or on essential carburetor parts. Purchase fuel in quantity that can be used within 30 days.

•Do not use gasoline which contains Methanol.

•Do not mix oil with gasoline.

•Your chipper shredder’s engine is certified to operate on gasoline. Exhaust Emission Control System: EM (Engine Modifications).

NOTE: Some fuels, called oxygenated or reformulated gasoline, are gasoline blended with alcohols or ethers. Excessive amounts of these blends can damage the fuel system or cause performance problems. If any undesirable operating symptoms occur, use gasoline with a lower percentage of alcohol or ether.

Fuel Fill-up

•Remove fuel cap from the fuel tank.

•Make sure the container from which you will pour the gasoline is clean and free from rust or foreign particles. Never use gasoline that may be stale from long periods of storage in its container. Gasoline that has been sitting for any period longer than four weeks is considered stale.

•The fuel tank has a capacity of three (3) quarts. Fill fuel tank with clean, fresh, unleaded regular, unleaded premium or reformulated automotive gasoline only.

•Replace fuel cap.

•To avoid engine problems, the fuel system should be emptied before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See STORAGE section for additional information.

WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes, and other sources of ignition.

Check the fuel level periodically to avoid running out of gasoline while operating the chipper shredder. If the unit runs out of gas while operating, it may be necessary to unclog the unit before it can be restarted.

Refer to SERVICE AND ADJUSTMENT section.

Starting Engine

WARNING: The muffler and surrounding area will be hot if the engine has been running. Use caution and protect your hands if working near the muffler.

•If not already attached, attach spark plug wire to spark plug. Make certain the rubber boot on the end of the spark plug is snapped securely over the metal tip on the spark plug. Refer to Figure 9 for spark plug wire location.

Spark Plug Wire

Figure 9

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Model No Horse PowerSears, Roebuck And Co., Hoffman Estates, IL 60179 U.S.A Table of Contents WarrantySafety TrainingOperation Page Loose Parts In Carton See Figure AssemblyRemoving Unit From Carton Lowering the Chipper ChuteEmptying the Debris Collection Bag HousingAttaching The Debris Collection Bag Debris Collection BagKnow Your Chipper Shredder Meets Ansi safety standardsOperation Operating Controls See FigureTamper Gas And Oil Fill-upStopping Engine HopperType of Fuel Starting EngineGasoline Fuel Fill-upShredding Clearing the HopperCleaning the Reduction Chamber ChippingAir Cleaner MaintenanceLubrication Spark Plug Cleaning EngineChanging Oil Replacing the Chipper Blades Service and AdjustmentsDisconnecting Spark Plug Replacing the Shredder BladeCarburetor Adjustment ChamberChipper Shredder StorageEngine Troubleshooting Problem Cause RemedySears Emission Control Defects Warranty Coverage Parts List Sears Craftsman 7.5 H.P. Chipper Shredder ModelPart Description Sears Craftsman 7.5 H.P. Chipper Shredder Model Carburetor Gasket SET 222 Repair Manual Cylinder Assembly Nut Governor Control Lever Engine Labels 777S32258 777D07574 777S32272Garantía limitada de la cortadora trituradora Craftsman ÍndiceGarantía 247.776350Seguridad CapacitaciónFuncionamiento Motor Piezas sueltas en la caja Ver Figura MontajeExtracción de la unidad de la caja Deslizamiento hacia abajo del canal de la cortadoraVaciado de la bolsa de recolección de desechos Colocación de la bolsa de recolección de desechosCumple con los estándares de seguridad de Ansi OperaciónConozca las propiedades de la cortadora trituradora Controles de funcionamiento Ver FiguraDetención del motor Carga de gas y aceiteAceite se envía una botella de 20 onzas junto con la unidad Advertencia Sea sumamente Encendido del motorGasolina Tipo de combustibleLimpieza de la tolva TrituraciónCorte Cámara de reducciónLimpieza del canal de reducción Lubricación MantenimientoFiltro de aire Bujía de encendido Limpieza del motorCambio de aceite Reemplazo de la hoja de la trituradora Servicio Y AjustesReemplazo de las hojas de la cortadora Desconexión de la bujíaAjuste del carburador Almacenamiento Cortadora trituradoraGuía Para LA Solución DE Problemas Problema Causa RemedioResponsabilidades del Propietario de la Garantía Repair Protection Agreements Acuerdo De Protección Para ReparacionesSears Parts & Repair Center Your HomeOur Home MY-HOME1-800-469-4663

247.77635 specifications

The Bolens 247.77635 is a versatile and robust garden tractor designed to meet the needs of homeowners and landscaping enthusiasts alike. Known for its reliable performance and user-friendly features, this model caters to a wide range of outdoor tasks, from mowing lawns to hauling equipment.

At the heart of the Bolens 247.77635 is a powerful 24 horsepower engine, designed to deliver exceptional performance while maintaining fuel efficiency. This engine is mated to an automatic transmission system, providing seamless gear changes and allowing users to focus on their task without the hassle of manual shifting. The tractor's hydrostatic drive enhances maneuverability, making it suitable for navigating tight spaces and tackling uneven terrain.

One of the standout features of the Bolens 247.77635 is its 42-inch cutting deck. This deck allows for a wide cutting path, reducing mowing time while ensuring a clean and even cut. The deck is also adjustable, offering multiple height settings to accommodate different grass types and user preferences. The rear discharge chute efficiently directs clippings away from the mower, resulting in a neat finish and the option to mulch the clippings back into the lawn for added nutrients.

The tractor boasts a comfortable and ergonomic seating arrangement, allowing operators to handle extended periods of use without discomfort. The dashboard is equipped with easy-to-read gauges that provide essential information at a glance, including fuel level and engine status. This ensures that users can monitor their machine's performance without distractions.

Another significant characteristic of the Bolens 247.77635 is its versatility. The tractor is compatible with various attachments, such as snowblowers, tillers, and bagging systems. This adaptability transforms the garden tractor into a year-round workhorse, equipped to handle winter snow removal as well as spring and summer landscaping tasks.

Safety features have been carefully integrated into the design, ensuring a secure operating environment. The tractor includes a rollover protection system, a seatbelt, and easy-access controls that promote safe operation even in challenging conditions.

In conclusion, the Bolens 247.77635 is a feature-rich garden tractor combining power, comfort, and versatility. Its user-friendly design, coupled with robust capabilities, makes it an ideal choice for homeowners seeking efficiency and reliability in their outdoor maintenance efforts. With the Bolens 247.77635, tackling any yard task becomes a manageable and enjoyable experience.
Top Page Image Contents