Bolens 247.77635 manual Cleaning Engine, Spark Plug, Changing Oil

Page 14

•Lift air cleaner assembly (air cleaner cartridge and precleaner) off stud.

•Push clean (or new) air cleaner assembly onto stud. Air cleaner must fit securely on base.

•Push cover squarely onto base and tighten knob.

NOTE: Clean pre-cleaner every few hours under extremely dusty conditions. To clean pre-cleaner, separate it from cartridge and wash in liquid detergent and water. Air dry thoroughly. Do not oil pre-cleaner. Re-assemble dry pre-cleaner onto clean cartridge.Replace the air cleaner cartridge once a season.

IMPORTANT: Do not use pressurized air or solvents to clean cartridge. Pressurized air can damage cartridge. Solvents will dissolve cartridge.

Cleaning Engine

•Promptly wipe off any fuel or oil spilled on the machine with clean cloth.

•Using a brush or cloth, remove debris from the finger guard on the engine daily to prevent overheating of the engine. Do not use water to clean engine parts. Water could contaminate the fuel system.

•Keep the throttle linkage, springs and controls free of debris.

•Clean muffler area and remove any debris before operating the unit.

Spark Plug

•Clean area around the spark plug base.

•Remove and inspect the spark plug.

•Replace the spark plug if electrodes are pitted, burned, or the porcelain is cracked. See Figure 15.

•Clean the spark plug and reset the gap to.030" at least once a season or every 100 hours of operation. See Figure 15. Replace if necessary. Refer to parts list section for part number.

NOTE: Do not sandblast spark plug. Spark plug should be cleaned by scraping or wire brushing and washing with a commercial solvent.

.030” (0.76 mm)

Figure 15

Changing Oil

To drain oil from the engine’s crankcase, proceed as follows:

•Run the engine for a few minutes to allow the oil to warm up. Warm oil flows more easily and will carry away more impurities when draining oil.

•Position the chipper shredder on level surface and place an appropriate receptacle with a capacity of at least one quart beneath the oil drain tube. See Figure 16.

Oil Dipstick

Oil Drain Tube

Figure 16

•Remove the oil dipstick.

•Use a 3/8” wrench to unthread the oil plug from the drain tube, allowing the used oil to flow out.

•Replace the oil plug and add 20 oz. of new oil (Refer to Page 9 for proper oil type). Do NOT overfill.

•Replace dipstick and check oil level (Refer to Page 9).

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Sears, Roebuck And Co., Hoffman Estates, IL 60179 U.S.A Horse PowerModel No Table of Contents WarrantySafety TrainingOperation Page Loose Parts In Carton See Figure AssemblyRemoving Unit From Carton Lowering the Chipper ChuteEmptying the Debris Collection Bag HousingAttaching The Debris Collection Bag Debris Collection BagKnow Your Chipper Shredder Meets Ansi safety standardsOperation Operating Controls See FigureTamper Gas And Oil Fill-upStopping Engine HopperType of Fuel Starting EngineGasoline Fuel Fill-upShredding Clearing the HopperCleaning the Reduction Chamber ChippingLubrication MaintenanceAir Cleaner Changing Oil Cleaning EngineSpark Plug Replacing the Chipper Blades Service and AdjustmentsDisconnecting Spark Plug Replacing the Shredder BladeCarburetor Adjustment ChamberEngine StorageChipper Shredder Troubleshooting Problem Cause RemedySears Emission Control Defects Warranty Coverage Parts List Sears Craftsman 7.5 H.P. Chipper Shredder ModelPart Description Sears Craftsman 7.5 H.P. Chipper Shredder Model Carburetor Gasket SET 222 Repair Manual Cylinder Assembly Nut Governor Control Lever Engine Labels 777S32258 777D07574 777S32272Garantía limitada de la cortadora trituradora Craftsman ÍndiceGarantía 247.776350Seguridad CapacitaciónFuncionamiento Motor Piezas sueltas en la caja Ver Figura MontajeExtracción de la unidad de la caja Deslizamiento hacia abajo del canal de la cortadoraVaciado de la bolsa de recolección de desechos Colocación de la bolsa de recolección de desechosCumple con los estándares de seguridad de Ansi OperaciónConozca las propiedades de la cortadora trituradora Controles de funcionamiento Ver FiguraAceite se envía una botella de 20 onzas junto con la unidad Carga de gas y aceiteDetención del motor Advertencia Sea sumamente Encendido del motorGasolina Tipo de combustibleLimpieza de la tolva TrituraciónCorte Cámara de reducciónLimpieza del canal de reducción Filtro de aire MantenimientoLubricación Cambio de aceite Limpieza del motorBujía de encendido Reemplazo de la hoja de la trituradora Servicio Y AjustesReemplazo de las hojas de la cortadora Desconexión de la bujíaAjuste del carburador Almacenamiento Cortadora trituradoraGuía Para LA Solución DE Problemas Problema Causa RemedioResponsabilidades del Propietario de la Garantía Repair Protection Agreements Acuerdo De Protección Para ReparacionesSears Parts & Repair Center Your HomeOur Home MY-HOME1-800-469-4663

247.77635 specifications

The Bolens 247.77635 is a versatile and robust garden tractor designed to meet the needs of homeowners and landscaping enthusiasts alike. Known for its reliable performance and user-friendly features, this model caters to a wide range of outdoor tasks, from mowing lawns to hauling equipment.

At the heart of the Bolens 247.77635 is a powerful 24 horsepower engine, designed to deliver exceptional performance while maintaining fuel efficiency. This engine is mated to an automatic transmission system, providing seamless gear changes and allowing users to focus on their task without the hassle of manual shifting. The tractor's hydrostatic drive enhances maneuverability, making it suitable for navigating tight spaces and tackling uneven terrain.

One of the standout features of the Bolens 247.77635 is its 42-inch cutting deck. This deck allows for a wide cutting path, reducing mowing time while ensuring a clean and even cut. The deck is also adjustable, offering multiple height settings to accommodate different grass types and user preferences. The rear discharge chute efficiently directs clippings away from the mower, resulting in a neat finish and the option to mulch the clippings back into the lawn for added nutrients.

The tractor boasts a comfortable and ergonomic seating arrangement, allowing operators to handle extended periods of use without discomfort. The dashboard is equipped with easy-to-read gauges that provide essential information at a glance, including fuel level and engine status. This ensures that users can monitor their machine's performance without distractions.

Another significant characteristic of the Bolens 247.77635 is its versatility. The tractor is compatible with various attachments, such as snowblowers, tillers, and bagging systems. This adaptability transforms the garden tractor into a year-round workhorse, equipped to handle winter snow removal as well as spring and summer landscaping tasks.

Safety features have been carefully integrated into the design, ensuring a secure operating environment. The tractor includes a rollover protection system, a seatbelt, and easy-access controls that promote safe operation even in challenging conditions.

In conclusion, the Bolens 247.77635 is a feature-rich garden tractor combining power, comfort, and versatility. Its user-friendly design, coupled with robust capabilities, makes it an ideal choice for homeowners seeking efficiency and reliability in their outdoor maintenance efforts. With the Bolens 247.77635, tackling any yard task becomes a manageable and enjoyable experience.
Top Page Image Contents