Bolens 247.77635 manual Chipping, Cleaning the Reduction Chamber

Page 12

Chipping

WARNING: Never operate the chipper shredder without chipper chute lowered into the operating position.

Branches up to 3” in diameter can be fed into the chipper chute. See Figure 6.Observe the following guidelines when chipping branches:

•Keep both hands firmly on the branch as you feed it into the chipper chute.

•Never feed more than one branch into the chipper chute at a time.

•Never feed anything other than branches (or wood) into the chipper chute.

•Use the tamper to assist in feeding branches into the chipper chute.

•Apply intermittent pressure (force, in short pulses) while feeding larger (2- 3-inch diameter) branches into the chipper chute, to avoid bogging or stalling the engine.

IMPORTANT: Never feed branches with a diameter greater than three (3) inches into the chipper chute. Doing so can result in serious damage to your unit’s chipper blades, flails or impeller.

NOTE: For best performance, always operate the unit with sharp chipper blades. If a noticeable loss in performance is encountered while chipping branches, the chipper blades should be replaced.

Cleaning the Reduction Chamber

WARNING: The impeller’s shredder blade and chipper blades are sharp. Wear leather work gloves to protect your hands when cleaning out the reduction chamber.

If the reduction chamber becomes clogged with debris, the shredder screen can be pivoted upward so that you can clean the surrounding area. To do so, proceed as follows:

•Stop the engine and wait until all moving parts have come to a complete stop.

•Disconnect spark plug wire and keep away from spark plug. Refer to Page 15.

WARNING: The muffler and surrounding area will be hot if the engine has been running. Use caution and protect your hands if working near the muffler.

•Remove the two wing knobs on either side of the chute deflector and pivot the chute deflector upward. See Figure 12.

•Remove the hairpin clip from the clevis pin which extends through the housing and shredder screen. See Figure 12. Retain the clevis pin and hairpin clip.

Chute

Deflector

Shredder

Screen

Hairpin

Clip

Housing

Clevis

Pin

Wing Knobs

Reduction

Chamber

Figure 12

•Pivot the shredder screen upward and clean the surrounding area by scraping away debris.

•Confirm that the spark plug wire is disconnected and away from spark plug.

•Pull on the starter rope two-to-three times to purge any remaining debris from the reduction chamber

•When the area is cleaned, pivot the shredder screen downward and re-secure with the clevis pin and hairpin clip removed earlier.

•Reattach the debris collection bag to the chute deflector, if desired.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Horse Power Model NoSears, Roebuck And Co., Hoffman Estates, IL 60179 U.S.A Table of Contents WarrantySafety TrainingOperation Page Assembly Removing Unit From CartonLoose Parts In Carton See Figure Lowering the Chipper ChuteHousing Attaching The Debris Collection BagEmptying the Debris Collection Bag Debris Collection BagMeets Ansi safety standards OperationKnow Your Chipper Shredder Operating Controls See FigureGas And Oil Fill-up Stopping EngineTamper HopperStarting Engine GasolineType of Fuel Fuel Fill-upShredding Clearing the HopperCleaning the Reduction Chamber ChippingMaintenance Air CleanerLubrication Cleaning Engine Spark PlugChanging Oil Service and Adjustments Disconnecting Spark PlugReplacing the Chipper Blades Replacing the Shredder BladeCarburetor Adjustment ChamberStorage Chipper ShredderEngine Troubleshooting Problem Cause RemedySears Emission Control Defects Warranty Coverage Parts List Sears Craftsman 7.5 H.P. Chipper Shredder ModelPart Description Sears Craftsman 7.5 H.P. Chipper Shredder Model Carburetor Gasket SET 222 Repair Manual Cylinder Assembly Nut Governor Control Lever Engine Labels 777S32258 777D07574 777S32272Índice GarantíaGarantía limitada de la cortadora trituradora Craftsman 247.776350Seguridad CapacitaciónFuncionamiento Motor Montaje Extracción de la unidad de la cajaPiezas sueltas en la caja Ver Figura Deslizamiento hacia abajo del canal de la cortadoraVaciado de la bolsa de recolección de desechos Colocación de la bolsa de recolección de desechosOperación Conozca las propiedades de la cortadora trituradoraCumple con los estándares de seguridad de Ansi Controles de funcionamiento Ver FiguraCarga de gas y aceite Detención del motorAceite se envía una botella de 20 onzas junto con la unidad Encendido del motor GasolinaAdvertencia Sea sumamente Tipo de combustibleTrituración CorteLimpieza de la tolva Cámara de reducciónLimpieza del canal de reducción Mantenimiento LubricaciónFiltro de aire Limpieza del motor Bujía de encendidoCambio de aceite Servicio Y Ajustes Reemplazo de las hojas de la cortadoraReemplazo de la hoja de la trituradora Desconexión de la bujíaAjuste del carburador Almacenamiento Cortadora trituradoraGuía Para LA Solución DE Problemas Problema Causa RemedioResponsabilidades del Propietario de la Garantía Repair Protection Agreements Acuerdo De Protección Para ReparacionesYour Home Our HomeSears Parts & Repair Center MY-HOME1-800-469-4663

247.77635 specifications

The Bolens 247.77635 is a versatile and robust garden tractor designed to meet the needs of homeowners and landscaping enthusiasts alike. Known for its reliable performance and user-friendly features, this model caters to a wide range of outdoor tasks, from mowing lawns to hauling equipment.

At the heart of the Bolens 247.77635 is a powerful 24 horsepower engine, designed to deliver exceptional performance while maintaining fuel efficiency. This engine is mated to an automatic transmission system, providing seamless gear changes and allowing users to focus on their task without the hassle of manual shifting. The tractor's hydrostatic drive enhances maneuverability, making it suitable for navigating tight spaces and tackling uneven terrain.

One of the standout features of the Bolens 247.77635 is its 42-inch cutting deck. This deck allows for a wide cutting path, reducing mowing time while ensuring a clean and even cut. The deck is also adjustable, offering multiple height settings to accommodate different grass types and user preferences. The rear discharge chute efficiently directs clippings away from the mower, resulting in a neat finish and the option to mulch the clippings back into the lawn for added nutrients.

The tractor boasts a comfortable and ergonomic seating arrangement, allowing operators to handle extended periods of use without discomfort. The dashboard is equipped with easy-to-read gauges that provide essential information at a glance, including fuel level and engine status. This ensures that users can monitor their machine's performance without distractions.

Another significant characteristic of the Bolens 247.77635 is its versatility. The tractor is compatible with various attachments, such as snowblowers, tillers, and bagging systems. This adaptability transforms the garden tractor into a year-round workhorse, equipped to handle winter snow removal as well as spring and summer landscaping tasks.

Safety features have been carefully integrated into the design, ensuring a secure operating environment. The tractor includes a rollover protection system, a seatbelt, and easy-access controls that promote safe operation even in challenging conditions.

In conclusion, the Bolens 247.77635 is a feature-rich garden tractor combining power, comfort, and versatility. Its user-friendly design, coupled with robust capabilities, makes it an ideal choice for homeowners seeking efficiency and reliability in their outdoor maintenance efforts. With the Bolens 247.77635, tackling any yard task becomes a manageable and enjoyable experience.
Top Page Image Contents