Notes:
–For recording, use only tape of IEC type I (normal tape) or IEC type II (Cr02).
–The tape is secured at both ends with leader tape. At the beginning and end of tape, nothing will be recorded for six to seven seconds.
–The recording level is set automatically, regardless of the position of Volume, Incredible Surround or Bass/Treble.
–To prevent accidental recording, break out the tab on the left shoulder of the tape side you want to protect.
–If “CHECK TAPE” is displayed, the protection tab has been broken. Put a piece of clear adhesive tape over the
opening. Do not cover the Cr02 tape detection hole when covering the tab opening.
One Touch Recording
•For One Touch Recording, as soon as you press REC, the current source (3 CDC, TUNER or CDR/AUX) will be recorded on tape deck 2
1Load a blank tape in tape deck 2.
2Press REC to start recording. ª The REC flag starts flashing.
3Press STOP to stop recording.
Note:
Recording from other sources
(only on tape deck 2)
1Press TAPE to select tape deck 2.
2Load a blank tape into tape deck 2 with the open side downward.
3Press SIDE on remote control to select the recording side.
ªThe BACK or FRONT flag will be displayed, depending on the side selected.
4Press 3 CDC, TUNER or CDR/AUX.
• Start playback of the selected source.
5Press REC to start recording.
ªThe REC flag starts flashing.
6Press STOP to stop recording.
Notes:
–Only Œ or • mode is available during recording.
–During recording, it is not possible to listen to another source.
Dubbing tapes (from tape deck 1 to tape deck 2)
1Press TAPE to select tape deck 2.
2Load the prerecorded tape into tape
deck 1 and a blank tape into tape deck 2.
•Make sure the tape in tape deck 1 has
its full spool to the left.
3 (For Tape Deck 2 only) |
4Press DUBBING NORMAL•FAST once for normal speed dubbing or twice (within 2 seconds) for high speed dubbing.
ª“NORMAL” (normal speed) or “FAST” (high speed) will be displayed, followed by “DUBBING”.
ªThe HSD flag appears on the display during high speed dubbing.
•Dubbing will start immediately.
ªThe REC flag starts flashing. 5 Press STOP to stop dubbing.
Notes:
–Only Œ mode is available during dubbing.
–At the end of side A, flip the tapes to side B and repeat the procedure.
–Dubbing of tapes is only possible from tape deck 1 to tape deck 2.
–To ensure good dubbing, use tapes of the same length.
–During high speed dubbing in Tape mode, the sound is reduced to a low volume.
–You can listen to another source while dubbing.
RECORDING
CD Synchro Start Recording
During CD synchro start recording,
•Do not fast forward/rewind your tape in tape deck 1.
•Do not listen to another source.
1Press TAPE to select tape deck 2.
•Load a blank tape into tape deck 2 with the open side downward.
2Press SIDE on remote control to select the recording side.
3Press A. REV to select the playback mode ( Œ or • ).
4Press 3 CDC.
•You can program the tracks in the order you want them to be recorded (see Programming Tracks). If you do not, the tracks are recorded according to the
order on the selected disc.
5Press CD SYN to start recording. ª The REC flag starts flashing.
6Press STOP to stop recording CD playback.
Digital Recording via Digital Out
For CD digital recording, please refer to the Instructions Manual of the CD Recorder, digital audio equipment, etc.
English
–When you press RECORD while in TAPE mode, "SELECT SOURCE" will be displayed. One Touch Recording is not possible in TAPE mode.
Press SIDE on the remote control to |
select the recording side. |
23