Magnavox MZ7 manual Setting the Timer, Viewing the Clock, Setting the Clock, automatically

CLOCK

English

3 CDC

TUNER

TAPE

CDR/AUX

CD CHANGER
FRONT BACK								NEWS	DIM
								T.A.	SLEEP
REC HSD	TRACK	PRESET REPEAT	AM LW	MW FM	STEREO	PROGRAM	TIMER SHUFFLE
INCREDIBLE
SURROUND
LOUDNESS
FLAT
SOUND	60Hz	250Hz	500Hz	1KHz	2KHz	4KHz	8KHz	VOLUME

▲	PRESET ▲	A•B
			DIGITAL CONTROL
SEARCH/TUNE		PLAY /	DIM	PROG/A.REV REC/CD SYN
	PRESET	STOP		FLAT
	BASS			TREBLE
		INCREDIBLE	LOUDNESS
		SURROUND

CLOCK/

TIMER

DUBBING

NORMAL•FAST

TIMER

Setting the Timer

•The system can switch on to CD, TUNER, or TAPE 2 mode automatically at a preset time. It can serve as an alarm to wake you up.

•Before setting the timer, make sure the clock is set correctly.

•The timer will always be switched on once it is set.

•The volume of the timer will start to increase from the minimum level until the volume level before the set is switched to standby mode.

5Press CLOCK/TIMER to store the start time.

ªThe timer is now set.

ªThe TIMER flag remains on the display.

• To exit without storing the setting, press STOP.

•At the preset time, the timer will be activated.

ª The selected source will be played.

Notes:

– During timer setting, if no button is

pressed within 90 seconds, the system

will exit timer setting mode

automatically.

Viewing the Clock

You can view the clock (if it is set) while the system is in standby mode or any source mode. It will be displayed for about seven seconds.

•Press CLOCK/TIMER briefly (on the system only).

ª“PM 10:38” (the current time) will be displayed.

ª“--:--” will be displayed if the clock is not set.

Setting the Clock

The clock is set in 12-hour mode, e.g. “AM 12:00“ or “PM12:00“. Before setting the clock, you must be in the View Clock mode.

24

1Press CLOCK/TIMER to select clock mode.

ª“PM 12:00” or the current time starts flashing.

2Press S or T to set the hour (PRESET mode OFF).

3Press S or T to set the minute (PRESET mode ON).

4Press CLOCK/TIMER again to store the setting.

ªThe clock starts.

•To exit without storing the setting, press STOP on the system.

Notes:

–During clock setting, if no button is pressed within 90 seconds, the system will exit clock setting mode automatically.

–When a power interruption occurs, the clock setting is erased.

1Press and hold CLOCK/TIMER for more than 2 seconds to select timer mode.

ª“AM 12:00” or the last set timer starts flashing. The TIMER flag flashes.

ªThe last selected source is lit while other available sources are flashing.

2Press 3 CDC, TUNER or TAPE to select the desired source.

•Before selecting CD or TAPE, make sure a CD or tape is loaded in the CD tray or tape deck 2.

3Press S or T to set the hour for the timer to start (PRESET mode OFF).

4Press S or T to set the minute for the timer to start (PRESET mode ON).

– If the source selected is TUNER, the last

tuned frequency will be switched on.

– If the source selected is CD, playback

will begin with the first track of the last

selected disc. If the CD trays are empty,

the TUNER will be selected instead.

– If the source selected is TAPE, and if the

preset time is reached during high

speed dubbing, the TUNER will be

selected instead.

– If the recording is active, the timer will

be cancelled.