Ariens 911413 warranty Operation, Controls and Features, Cutting Height Adjustment

Page 13

OPERATION

CONTROLS AND FEATURES

See Figure 6 for locations.

WARNING: Improper operation can lead to injury. Learn what the controls do and how they work. Thoroughly read and understand entire Operator Manual.

CAUTION: AVOID INJURY. Read and understand the entire Safety section before proceeding.

Parking Brake Lever (Right Hand Lever)

Hold the parking brake lever against the handlebar to release the wheel lock pin and operate the unit.

Release the parking brake lever to engage wheel lock pin and prevent the unit from rolling forward or backward.

IMPORTANT: The wheel lock pin prevents the unit from rolling forward or backward. The unit can still pivot from side to side.

Parking Brake Engaged: Unit will not roll forward or backward.

Parking Brake Disengaged: Hold lever against handlebar to operate the unit.

PTO Clutch Lever (Left Hand Lever)

Hold down the lock lever and then squeeze the PTO clutch lever against the handlebar to engage the clutch and start the mower blades.

Release the clutch lever to stop the blades.

NOTE: The lock lever prevents the PTO clutch lever from being squeezed accidentally. It will engage each time you release the clutch lever.

PTO Disengaged: Mower blades stop rotating.

PTO Engaged: Hold down the lock lever and then hold clutch lever against handlebar to engage the clutch and start the mower blades.

CUTTING HEIGHT ADJUSTMENT

DANGER: Avoid injury from rotating blade.

ALWAYS shut off engine before adjusting cutting height.

Cutting Height Settings Chart

Spacers

Cut Grass Length

Below Caster

 

Arms

 

0

1-3/4" (44.4 mm)

1

2" (50.8 mm)

2

2-1/2" (63.5 mm)

3

2-3/4" (69.8 mm)

4

3" (76.2 mm)

5

3-1/4" (82.6 mm)

6

3-1/2" (88.9 mm)

NOTE: Placing the spacers above the caster arm lowers the deck and decreases cutting height. Placing the spacers below the caster arm raises the deck and increases the cutting height.

To change cutting height, remove the lock pin from the top of the caster fork. Raise the caster arm high enough to expose the flats and lower pin hole on the caster fork spindle. Insert the lock pin into the lower hole to support the arm while adjusting the cutting height spacers (Figure 7).

GB - 13

Image 13
Contents Wide Area Walk Mower Introduction Table of ContentsProduct Registration Unauthorized Replacement Parts Dealer DeliveryDisclaimer Safety Alerts SafetyNotations Practices and LawsDismemberment Hazard Safety Decals LocationsDischarge Hazard Emission Control System Safety RulesPage Page Carton Contents AssemblyAssembly Negative Battery Cable Figure Controls and Features Cutting Height Adjustment Controls and FeaturesOperation Parking Brake Lever Right Hand LeverPage Forward Drive Control Lower Right Hand Control Filling the Fuel TankReverse Drive Control Side Right Hand Control Emergency Stopping GasolineStarting and Shut OFF Maintenance Schedule MaintenanceSharpen the Mower Blades Check Drive Belts Check AIR CleanerCheck Fasteners Change Engine OILForward/Reverse Drive Controls Service and AdjustmentsWheel Drive Belts Belt ReplacementReplacing Mower Blade Install FigurePTO Belt Deck Belt Remove FigureU1 Battery Removal and Installation Figure Remove Servicing the BatteryInstall Install U1-Size Battery Figure Charging the Battery Cleaning Battery and Battery Cables or FigureJump-Starting Storage TroubleshootingAccessories Service PartsSpecifications Consumer Mowing Equipment Limited Warranty Limitation of Remedy and Damages

911413 specifications

The Ariens 911413 is a powerful and robust snow blower designed to tackle some of the toughest winter conditions. Renowned for its performance and durability, this machine is a favorite among homeowners who face heavy snowfall. One of its main features is the strong 420cc Ariens AX420 engine, which provides ample power for clearing snow with ease. This engine is designed for reliability and efficiency, ensuring that the machine can get the job done without the need for frequent maintenance.

The Ariens 911413 boasts a 24-inch clearing width, allowing it to handle large areas quickly. It can throw snow up to 50 feet, making it an ideal choice for those with long driveways or large outdoor spaces. The snow blower is equipped with a heavy-duty steel auger system that efficiently breaks up and collects snow, ensuring that no snow is left behind. This construction guarantees superior performance even in the most challenging winter conditions.

In terms of technology, the Ariens 911413 features a 6-speed forward and 2-speed reverse transmission, providing users with greater control and flexibility when navigating through deep snow. The self-propelled system allows for effortless movement, reducing user fatigue during operation. Additionally, the machine includes an adjustable discharge chute that can be rotated 200 degrees, enabling users to direct the snow precisely where they want it to go.

Another notable characteristic of the Ariens 911413 is its ergonomic design. The machine comes with heated hand grips, which add comfort during use in frigid temperatures. The quick-release chute clean-out tool simplifies maintenance and ensures that the discharge chute remains clear during operation.

Durability is a key feature of the Ariens 911413, with its heavy-gauge steel frame and reinforced auger housing designed to withstand rigorous use over the years. The snow blower is built to last, giving users peace of mind as they invest in a reliable winter tool. When it comes to performance, features, and efficiency, the Ariens 911413 stands out as a top choice for winter snow removal, providing excellent value and performance for those looking to conquer cold weather challenges.