Ariens 911413 warranty Check Drive Belts, Check Fasteners, Check AIR Cleaner, Change Engine OIL

Page 19

CHECK DRIVE BELTS

Check drive belts and replace if worn or damaged. See Wheel Drive Belts on page 21.

CHECK FASTENERS

Check all fasteners for proper tightness. Pay special attention to blade hardware and all guards, shields and safety devices.

CHECK AIR CLEANER

See engine manual for specific information.

CHANGE ENGINE OIL

IMPORTANT: Change engine crankcase oil after first five (5) hours of operation. Then change oil after every 25 hours of operation.

Refer to engine manual for instructions and proper oil type.

IMPORTANT: Proper oil level must be maintained at all times or engine damage will result. DO NOT overfill. Be sure engine is level when adding oil.

GENERAL LUBRICATION

The unit has sealed maintenance-free spindles and transmission. The unit should not require lubrication except for light oil or grease at pivot points.

CHECK SPARK PLUG

Spark plug should be replaced every 100 hours of operation or each year.

NOTE: Loose spark plug wire terminals can cause sparking. Replace terminal if damaged.

CHECK ENGINE COOLING

WARNING: HOT SURFACES can cause death or serious injury. DO NOT TOUCH parts which are hot from operation. ALWAYS allow parts to cool.

To prevent overheating, air must circulate freely around the cooling fins, cylinder head and block.

Every 100 hours of operation or yearly (more often if conditions require) remove blower housing and clean cooling fins. See engine manual for instructions.

CHECK MUFFLER

Check muffler for debris, cracks, wear, or other damage.

CAUTION: Replace worn-out mufflers immediately. Continued use could result in fire or explosion.

GB - 19

Image 19
Contents Wide Area Walk Mower Introduction Table of ContentsProduct Registration Unauthorized Replacement Parts Dealer DeliveryDisclaimer Practices and Laws SafetySafety Alerts NotationsDismemberment Hazard Safety Decals LocationsDischarge Hazard Emission Control System Safety RulesPage Page Carton Contents AssemblyAssembly Negative Battery Cable Figure Controls and Features Parking Brake Lever Right Hand Lever Controls and FeaturesCutting Height Adjustment OperationPage Forward Drive Control Lower Right Hand Control Filling the Fuel TankReverse Drive Control Side Right Hand Control Emergency Stopping GasolineStarting and Shut OFF Maintenance Schedule MaintenanceSharpen the Mower Blades Change Engine OIL Check AIR CleanerCheck Drive Belts Check FastenersForward/Reverse Drive Controls Service and AdjustmentsWheel Drive Belts Belt ReplacementRemove Figure Install FigureReplacing Mower Blade PTO Belt Deck BeltU1 Battery Removal and Installation Figure Remove Servicing the BatteryInstall Install U1-Size Battery Figure Charging the Battery Cleaning Battery and Battery Cables or FigureJump-Starting Storage TroubleshootingAccessories Service PartsSpecifications Consumer Mowing Equipment Limited Warranty Limitation of Remedy and Damages

911413 specifications

The Ariens 911413 is a powerful and robust snow blower designed to tackle some of the toughest winter conditions. Renowned for its performance and durability, this machine is a favorite among homeowners who face heavy snowfall. One of its main features is the strong 420cc Ariens AX420 engine, which provides ample power for clearing snow with ease. This engine is designed for reliability and efficiency, ensuring that the machine can get the job done without the need for frequent maintenance.

The Ariens 911413 boasts a 24-inch clearing width, allowing it to handle large areas quickly. It can throw snow up to 50 feet, making it an ideal choice for those with long driveways or large outdoor spaces. The snow blower is equipped with a heavy-duty steel auger system that efficiently breaks up and collects snow, ensuring that no snow is left behind. This construction guarantees superior performance even in the most challenging winter conditions.

In terms of technology, the Ariens 911413 features a 6-speed forward and 2-speed reverse transmission, providing users with greater control and flexibility when navigating through deep snow. The self-propelled system allows for effortless movement, reducing user fatigue during operation. Additionally, the machine includes an adjustable discharge chute that can be rotated 200 degrees, enabling users to direct the snow precisely where they want it to go.

Another notable characteristic of the Ariens 911413 is its ergonomic design. The machine comes with heated hand grips, which add comfort during use in frigid temperatures. The quick-release chute clean-out tool simplifies maintenance and ensures that the discharge chute remains clear during operation.

Durability is a key feature of the Ariens 911413, with its heavy-gauge steel frame and reinforced auger housing designed to withstand rigorous use over the years. The snow blower is built to last, giving users peace of mind as they invest in a reliable winter tool. When it comes to performance, features, and efficiency, the Ariens 911413 stands out as a top choice for winter snow removal, providing excellent value and performance for those looking to conquer cold weather challenges.