Meridian Audio G61 manual Left Level +0.0dB, Wizard complete, To start the calibration procedure

Page 31

2 6

C a l i b r a t i n g t h e s y s t e m

To start the calibration procedure

Either:

•Press Next on the last option of configuring settings; see page 22.

Or:

•Press On/Off to put the digital surround controller into standby.

•Press More.

If the product is locked the display shows:

VersionUnlock

•Press Unlock.

The display shows:

Version

Wizard Calib Lock

• Press Calib.

The displays shows Please wait….

After a few seconds the display shows the first calibration test:

Press More for help

Left Level +0.0dB

For more detailed information about this and the other calibration tests see the following sections.

To exit from the calibration procedure

You can exit from the calibration procedure at any time, and any parameters you have set will be retained:

• Press On/Off.

To complete the calibration procedure

When you reach the end of the calibration procedure the following display confirms that you have completed the calibration of the system:

Calibration complete.

Back Next

Restart

•Press Restart to restart the calibration procedure, or Next to complete the wizard.

The display shows:

Press More for help

Wizard complete

Back Exit Restart

Either:

• Press Exit to return to standby.

Or:

ìî	ïñ óòô öõú	• Press Restart to return to stage 1; see page 16.
		• Press Restart to return to stage 1; see page 16.

Image 31

Contents R I D I a N G S E R I E S G61 Digital Surround Controller Installation Guide To avoid interference Safety warningsRefer all servicing to approved service personnel To avoid overheatingContents Tel +1 404 344 Fax +1 404 346 Part no G61/1 Sales and service in the UKSales and service in the USA Copyright and acknowledgementsFormats supported Smart Source featureIntroduction InputsT r o d u c t i o n Specifications T r o d u c t i o n Unpacking Installing the digital surround controllerAudio inputs Use this connectorTo connect to this To connect to an analogue source eg TV tuner To connect to a digital source eg G07 24-bit CD Player#$ $6$ ! Player Use this output Audio outputsTo connect the G61 to Meridian DSP loudspeakers $30 n -!.!2Phono Lead M33To connect an active subwoofer eg Meridian M1500 or M2500 3UBWOOFER $IGITALI3URROUND #ONTROLLERCommunications connections Use this connector To connect to thisScreen Auto To do this Configuring the digital surround controllerConfiguration Wizard To run the Configuration WizardType Reset settingsReset all settings? To reset the configurationType Speakers Music Sub Logic Sub TypesTo change an option To configure the speakersSelect speakers OneOption Values Description Speaker optionsRadio Use Configure sourcesTo configure a source Press Source When you have finished configuring sourcesOption Values Source optionsTo change a setting Stage 4 Configuring other settingsOther settings To configure other settingsSettings Page Calibrating the system Using a Sound Pressure Level meterIntroduction Left Level +0.0dB To start the calibration procedureTo exit from the calibration procedure To complete the calibration procedureLevels Calibration testsDistance Left Distance Fine tuningLeft Phase Setting What it sounds likeSizes set to zero Speaker sizeLeft Size CD Xover 85Hz Using the Sine/Sub/Sens controlsSinewave sweep test Subwoofer crossover frequencyPause 80.0Hz CD Sine 80.0Hz88.5Hz 81.5HzTV 2.0V Clip Setting up sourcesTo adjust the sensitivity of a source 4V PeakLayout Description DSP presetsDSP presets Speaker layoutsStandard parameters Parameter Range Default What it changesStandard-rate audio, downsampled if necessary Parameter Options What it changes Music and Trifield DSP preset parametersMusic TrifieldAmbisonics Ambisonics and Super DSP preset parametersSuper PLIIx Music MusicLogicSurrounds Rear, Side, All PLIIx Movie and PLIIx THX DSP preset parametersStereo and Direct PLIIx Movie and PLIIx THXParameter Options Mono DSP preset parametersTV Logic MonoCinema Discrete and Cinema DSP preset parametersDiscrete 28dB to 0dB THXUsing dynamic range control To save the preset settings Defining your own presetsFor example Stored To clear a user-defined presetFor example, you could change the name to Erratic or unexpected system behaviour TroubleshootingGeneral operating problems Standby light not litHum on analogue input Audio problemsRemote not working Unit is overheatingCentre not working Audible hiss at high volume settingsThere is a hiss when starting DTS LaserDiscs or CDs Sound not clearPreset changes unexpectedly with a multichannel Source To clean the audio and video connections MaintenanceCleaning To clean the case, display panel, and keypadService Service and guaranteeGuarantee Calibration procedure 25 moving between tests 26 starting Academy DSP parameter 39 accessoriesRear THX DSP parameters DSP presetsGuarantee +2+2 PLIIx Music PanoramaSubwoofer crossover frequency 30 Super DSP preset +2+2 DSP parameters THX DSP preset 40 UHJ format THX Music DSP presetTypes 16