Alamo manual 2500 01/11 Safety Section

Page 7
(SG-10)
(SG-8)
(SG-7)
(SG-6)

SAFETY

Never operate the Tractor or Implement until you have read and completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Messages found in the Manual or on the Tractor and Implement. Learn how to stop the tractor engine suddenly in an emergency. Never allow inexperienced or untrained personnel to operate the Tractor or Implement without supervision. Make sure the operator has fully read and understood the manuals prior to operation.

(SG-4)

Always maintain the safety signs in good readable condition. If the safety signs are missing, damaged, or unreadable, obtain and install replacement safety signs immediately. (SG-5)

Make certain that the “Slow Moving Vehicle” (SMV) sign is installed in such a way as to be clearly visible and legible. When transporting the Equipment use the Tractor flashing warning lights and follow all local traffic regulations.

Operate this Equipment only with a Tractor equipped with an approved roll- over-protective system (ROPS). Always wear seat belts. Serious injury or even death could result from falling off the tractor--particularly during a turnover when the operator could be pinned under the ROPS.

Do not modify or alter this Implement. Do not permit anyone to modify or alter this Implement, any of its components or any Implement function.

BEFORE leaving the tractor seat lower the implement, set the parking brake and/or set the tractor transmission in parking gear, disengage the PTO, stop the engine, remove the key, and wait for all moving parts to stop. Place the tractor shift lever into a low range or parking gear to prevent the tractor from rolling. Never dismount a Tractor that is moving or while the engine is running. Operate the Tractor controls from the tractor seat only. (SG-9)

Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death.

SAFETY

2500 01/11

Safety Section 1-3

© 2011 Alamo Group Inc.

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Rear Mounted Blade 2500To the Owner/Operator/Dealer Table of Contents Lubrication Proper Torque For Fasteners Safety Section Safety Messages Safety2500 01/11 Safety Section Safety Safety Safety S3PT-02 See Your Rhino Dealer Decal Location QTY Level Description Decal Description Safety Safety Safety Safety Federal Laws and Regulations Introduction Section Introduction IntroductionIntroduction Before Operating this Machine Assembly Section Assembly of Moldboard to Mainframe AssemblyAsm-0001 Skid Shoes & Quick Tack End Plates Extra Equipment Gauge Wheel Extra EquipmentHydraulic System Hydraulic Control Valve Extra Equipment Selector Valve Accessory EquipmentPage Operation Section Operation Operation Standard Equipment and SpecificationsPersonal Protective Equipment PPE Operator RequirementsTractor Requirements Tractor HorsepowerRops and Seat Belt Getting on and OFF the Tractor Front End WeightTractor 3-Point Hitch Dismounting the Tractor Boarding the TractorStarting the Tractor Connecting the Rear Blade to the TractorConnecting the Rear Blade Tractor Pre-Operation Inspection/Service PRE-OPERATION Inspection and ServiceBlade Pre-Operation Inspection/Service Do not Operate an Unsafe Tractor or Mower Do not Operate an Unsafe Tractor or Implement Driving the Tractor and Implement Starting the Tractor Brake and Differential Lock SettingDriving the Tractor and Blade Operating the Tractor and ImplementDitching V-Type Ditch Operating the BladeShutting Down the Implement Disconnecting the Blade from the TractorTransporting the Tractor and Implement Blade StorageTransporting on Public Roadways Operation Hauling the Tractor and Implement Operation Problem Possible Cause Remedy Troubleshooting GuideMaintenance Section Lubrication MaintenanceProper Torque For Fasteners Rhino RhinoTo the OWNER/OPERATOR/DEALER SOM-01/11 00767428C Printed U.S.A
Top Page Image Contents