Alamo 2500 manual Operating the Tractor and Implement, Driving the Tractor and Blade

Page 46

OPERATION

OPERATION

8.3 Driving the Tractor and Blade

Start off driving at a slow speed and gradually increase your speed while maintaining complete control of the tractor and blade. Moving slowly at first will also prevent the tractor from rearing up and loss of steering control. The tractor should never be operated at speeds that cannot be safely handled or which will prevent the operator from stopping quickly during an emergency. If the power steering or engine ceases operating, stop the tractor immediately as the tractor will be difficult to control.

Perform turns with the tractor and blade at slow speeds to determine how the tractor with an attached implement handles a turn. Determine the safe speed to maintain proper control of the tractor when making turns. When turning with an implement, the overall working length of the unit is increased. Allow additional clearance for the blade when turning.

To avoid overturns, drive the tractor with care and at safe speeds, especially when operating over rough ground, crossing ditches or slopes, and turning corners. Tractor wheel tread spacing should be increased when working on inclines or rough ground to reduce the possibility of tipping.

Use extreme caution when operating on steep slopes. Keep the tractor in a low gear when going downhill. DO NOT coast or free-wheel downhill. OPS- 0037_A

9. OPERATING THE TRACTOR AND IMPLEMENT

THE OPERATOR MUST COMPLETELY UNDERSTAND HOW TO OPERATE THE TRACTOR AND IMPLEMENT AND ALL CONTROLS BEFORE ATTEMPTING TO OPERATE. The operator must read and understand the Safety and Operation Sections of the implement and tractor operator’s manuals. These manuals must be read and explained to any operator who cannot read. Never allow someone to operate the implement and tractor without complete operating instructions.

Before starting any operation, the operator must become familiar with the area to be worked in and any obstacles and hazards contained within to ensure safety to the operator, bystanders, and equipment. Special attention should be paid to foreign debris, rough terrain, steep slopes, and passersby and animals in the area. OPS-U- 0015

2500 01/11

Operation Section 4-16

© 2011 Alamo Group Inc.

Image 46
Contents 2500 Rear Mounted BladeTo the Owner/Operator/Dealer Table of Contents Lubrication Proper Torque For Fasteners Safety Section Safety Safety Messages2500 01/11 Safety Section Safety Safety Safety S3PT-02 See Your Rhino Dealer Decal Location QTY Level Description Decal Description Safety Safety Safety Safety Federal Laws and Regulations Introduction Section Introduction IntroductionIntroduction Before Operating this Machine Assembly Section Assembly Assembly of Moldboard to MainframeAsm-0001 Skid Shoes & Quick Tack End Plates Extra Equipment Gauge Wheel Extra EquipmentHydraulic System Selector Valve Accessory Equipment Hydraulic Control Valve Extra EquipmentPage Operation Section Operation Standard Equipment and Specifications OperationOperator Requirements Personal Protective Equipment PPETractor Requirements Tractor HorsepowerRops and Seat Belt Getting on and OFF the Tractor Front End WeightTractor 3-Point Hitch Boarding the Tractor Dismounting the TractorConnecting the Rear Blade to the Tractor Starting the TractorConnecting the Rear Blade PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBlade Pre-Operation Inspection/Service Do not Operate an Unsafe Tractor or Mower Do not Operate an Unsafe Tractor or Implement Driving the Tractor and Implement Brake and Differential Lock Setting Starting the TractorOperating the Tractor and Implement Driving the Tractor and BladeOperating the Blade Ditching V-Type DitchDisconnecting the Blade from the Tractor Shutting Down the ImplementBlade Storage Transporting the Tractor and ImplementTransporting on Public Roadways Operation Hauling the Tractor and Implement Operation Troubleshooting Guide Problem Possible Cause RemedyMaintenance Section Maintenance LubricationProper Torque For Fasteners Rhino RhinoTo the OWNER/OPERATOR/DEALER SOM-01/11 00767428C Printed U.S.A