Alamo 2500 manual Getting on and OFF the Tractor, Tractor 3-Point Hitch, Front End Weight

Page 36
(SG-12)

OPERATION

OPERATION

3.3 Tractor 3-Point Hitch

The tractor 3-point hitch must be rated to lift at least 2260 lbs. for the 10’ and 2400 lbs. for the 12’.

The 2500 can attach to tractor’s with either a CAT II or III hitch. Refer to the tractor operator’s manual for the category of the tractor used. If the hitch does not conform to the ASABE CAT II or III dimensions, the blade may not fit or raise properly. Consult an authorized dealer for possible modification procedures to mount nonconforming hitches.

Use the correct hitch pins for the hitch category being used. For a Cat II hitch, 1-1/8” lower and a 1” upper diameter hitch pins are used and Cat III hitches require 1-7/16” lower and a 1-1/4” upper diameter hitch pins.

CAT II Implement / Hitch Specification

 

CAT III Implement/ Hitch Specification

 

Width from outside to outside A-frame

32-3/8”

Width from outside to outside A-frame

38”

Quick Hitch width inside lug to lug

33-5/8”

Quick Hitch width inside lug to lug

39-1/4”

Height from bottom hitch pin to top pin

19”

Height from bottom hitch pin to top pin

22”

Lower pin diameter

1-1/18”

Lower pin diameter

1-7/16”

Upper pin diameter

1”

Upper pin diameter

1-1/4”

Linch pin diameter

15/32”

Linch pin diameter

15/32”

3.4 Front End Weight

A minimum of 20% total tractor weight must be maintained on the tractor front end at all times. Front end weight is critical to maintain steering control and to prevent the tractor from rearing up while driving. If the front end is too light, add weight until a minimum of 20% total weight is reached on the front tires. Front weights and weight carriers can be purchased through an authorized tractor dealership. OPS-U- 0005

4. GETTING ON AND OFF THE TRACTOR

Before getting onto the tractor, the operator must read and completely understand the implement and tractor operator manuals. If any part of either manual is not completely understood, consult an authorized dealer for a complete explanation. OPS-U- 0007

Do not mount or dismount the Tractor while the tractor is moving. Mount the Tractor only when the Tractor and all moving parts are completelystopped.

2500 01/11

Operation Section 4-6

© 2011 Alamo Group Inc.

Image 36
Contents 2500 Rear Mounted BladeTo the Owner/Operator/Dealer Table of Contents Lubrication Proper Torque For Fasteners Safety Section Safety Safety Messages2500 01/11 Safety Section Safety Safety Safety S3PT-02 See Your Rhino Dealer Decal Location QTY Level Description Decal Description Safety Safety Safety Safety Federal Laws and Regulations Introduction Section Introduction IntroductionIntroduction Before Operating this Machine Assembly Section Assembly Assembly of Moldboard to MainframeAsm-0001 Gauge Wheel Extra Equipment Skid Shoes & Quick Tack End Plates Extra EquipmentHydraulic System Selector Valve Accessory Equipment Hydraulic Control Valve Extra EquipmentPage Operation Section Operation Standard Equipment and Specifications OperationOperator Requirements Personal Protective Equipment PPETractor Horsepower Tractor RequirementsRops and Seat Belt Front End Weight Getting on and OFF the TractorTractor 3-Point Hitch Boarding the Tractor Dismounting the TractorConnecting the Rear Blade to the Tractor Starting the TractorConnecting the Rear Blade PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/ServiceBlade Pre-Operation Inspection/Service Do not Operate an Unsafe Tractor or Mower Do not Operate an Unsafe Tractor or Implement Driving the Tractor and Implement Brake and Differential Lock Setting Starting the TractorOperating the Tractor and Implement Driving the Tractor and BladeOperating the Blade Ditching V-Type DitchDisconnecting the Blade from the Tractor Shutting Down the ImplementBlade Storage Transporting the Tractor and ImplementTransporting on Public Roadways Operation Hauling the Tractor and Implement Operation Troubleshooting Guide Problem Possible Cause RemedyMaintenance Section Maintenance LubricationProper Torque For Fasteners Rhino RhinoTo the OWNER/OPERATOR/DEALER SOM-01/11 00767428C Printed U.S.A