Dolmar PE-251 instruction manual Stopping, Adjustment of LOW-SPEED Rotation Idling

Page 12

–First place the machine on the ground.

–Give a gentle push on the primer pump (2) repeatedly (7-10 times) until fuel comes into the primer pump.

– Push the choke lever (3) to the position “

”.

 

(3)

(2)

–Firmly hold the clutch case by your left hand, as illustrated.

–Slowly pull the starter grip until resistance is felt and continue with a smart pull.

–Do not pull out the starter rope to its full extent and do not allow the starter handle to be retracted without control, but ensure that it is retracted slowly.

–Repeat the starting operation until initial ignitions are heard.

–When the engine start, return the choke lever to “ ”. Please note that the choke lever will return to “ ”position automatically when the throttle lever is operated and the throttle is opened.

–Run the engine for approximately one minute at a moderate speed before applying full throttle.

Note: – If the starter handle is pulled repeatedly when the choke lever remains at “ ” position, the engine will not start easily due to excessive fuel intake.

–In case of excessive fuel intake, remove the spark plug and pull the starter handle slowly to remove excess fuel. Also,dry the electrode section of the spark plug.

Caution during operation:

If the throttle lever is opened fully in a no-load operation, the engine rotation is increased to 10,000 /min or more. Never operate the engine at a higher speed than required and at an approximate speed of 6,000 - 8,000 /min.

Starting the warm engine

–Same as adove, except without moving the choke lever (choke lever remains in the position “ ” ).

STOPPING

–Release the throttle lever (6) fully, and when the engine rpm has lowered, push the I-O switch (1) to “O” position the engine will now stop.

–Be aware that the cutting head may not stop immediately and allow it to slow down fully.

ADJUSTMENT OF LOW-SPEED ROTATION (IDLING)

The cutter blade or the nylon cutting head should not run when the control lever is fully released. If necessary, adjust the idle rpm using the idle adjusting screw.

Checking the Idling speed

–Idle speed should be set to 2,600 /min.

If necessary correct it by means of the idle screw (the cutting blade must not turn when the engine is on idle).

Screwing in the screw (1) will cause an increase in the engine speed, whereas backing off the screw will reduce the engine speed.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PE-251 Symbols EnglishSafety Instructions General InstructionsIntended use of the machine Personal protective equipmentRefuelling Maintenance instructions When asking for help, please give the following informationMethod of operation Cutting BladeTechnical Data PE-251 ModelDesignation of Parts Designation of PartsAssembly of Engine and Shaft How to mount the control cableConnection of the switch cord Mounting of Handle Mounting of WheelMounting of Deflector FUELS/REFUELLING Handling fuelFuel and oil mixture Points in Operation and HOW to Stop Correct Handling of MachineAttachment of shoulder strap DetachmentAdjustment of LOW-SPEED Rotation Idling StoppingDaily checkup and maintenance Cleaning of air cleanerServicing Instructions Servicing InstructionsCleaning of muffler exhaust port Checking the spark plugSupply of grease to gear case Supply of grease to flexible shaftMaintenance schedule Fault locationStorage Federal Emission Component Defect Warranty Obtaining Warranty Service HOW to Make a Claim Symboles FrançaisConsignes DE Sécurité Instructions généralesUtilisation spéciale de la machine Équipement personnel de protectionRavitaillement MètresInstructions de maintenance Méthode d’utilisationLame de coupe Premier secourCaracteristiques Techniques PE-251 PE-251Nomenclature DES Pièces Montage du câble de commande Assemblage DU Moteur ET DE L’ARBRERaccordement de la corde d’interrupteur Montage DE LA Poignée Montage DU VolantMontage DU Déflecteur CARBURANTS/RAVITAILLEMENT Manipulation Correcte DE LA Machine Consignes DE Mise EN Marche ET Arrêt DE LA MachineFixation du harnais RetraitArrêt Reglage DE LA Marche a Petite Vitesse AU RalentiContrôle et opérations de maintenance réguliers Instructions Relatives AUX RéparationsInstructions Relatives AUX Réparations Nettoyage du filtre à airContôle de la bougie dallumage Graissage du carter de la boîte de vitesseTête daspiration dans le réservoir de carburant Nettoyage de lorifice du pot déchappementPlan de maintenance RemisageLocalisation des défauts Simbolos Lista de contenidos PáginaInstrucciones DE Seguridad Instrucciones generalesUso recomendado de la máquina Equipo Personal de ProtecciónReabastecimiento Método de trabajo Cuchilla de corteInstrucciones de mantenimiento Nunca rectificar o soldar las herramientas de corte dañadasDatos Técnicos PE-251 ModeloDenominación DE Partes Denominacion DE PartesMontaje DE Motor Y EJE Montaje del cable de controlEmpalme del cordón del interruptor Montaje DEL Manillar Montaje DE LA RuedaMontaje DEL Desviador COMBUSTIBLES/REABASTECIMIENTO USO Correcto DE LA Máquina Puntos Relacionados CON EL Manejo Y LA ParadaColocación de la correa para el hombro SeparaciónParo Ajuste DEL Giro a Baja Velocidad RalentíInstrucciones DE Servicio Instrucciones DE ServicioLimpieza del filtro de aire Comprobación de la Bujía Suministro de grasa a la caja de engranajesCabezal de succión en el tanque de combustible Limpieza del orificio de salida del silenciadorAlmacenamiento Page PO Box Alpharetta

PE-251 specifications

The Dolmar PE-251 is a versatile and powerful chainsaw designed for both professional and amateur use. Known for its reliability and robustness, this chainsaw is particularly well-suited for light to medium-duty tasks, making it an excellent choice for homeowners, gardeners, and small-scale forestry operations.

One of the standout features of the Dolmar PE-251 is its lightweight design, which enhances maneuverability and reduces user fatigue. Weighing in at just around 5.5 kg, it enables longer operating periods without compromising performance. The engine, with a displacement of 25.4 cc, delivers a high power-to-weight ratio, ensuring that users can tackle a range of cutting tasks, from trimming branches to felling smaller trees.

The Dolmar PE-251 is equipped with an advanced 2-stroke engine that not only provides exceptional power but also features low emissions, aligning with contemporary environmental standards. This technology ensures that users can work efficiently without contributing excessively to air pollution. The engine operates smoothly, thanks to a well-designed intake and exhaust system that optimizes fuel and air flow.

Another significant characteristic of the PE-251 is its easy-start mechanism, which features a primer bulb and a precision-engineered recoil starter. This technology reduces the effort required for starting the machine, allowing users to get to work quickly. Additionally, the chainsaw incorporates an adjustable oil pump that allows for accurate lubrication of the chain, enhancing performance and prolonging the life of the saw.

Safety is a priority with the Dolmar PE-251, evident in its built-in safety features. The chainsaw includes a chain brake, which can be activated instantly to stop the chain in case of kickback, a common hazard during cutting tasks. Furthermore, the handle is ergonomically designed for a comfortable grip, providing better control and reducing the risk of accidents.

In conclusion, the Dolmar PE-251 is an excellent choice for users seeking a reliable, lightweight chainsaw with innovative features that enhance performance and safety. Whether for maintaining a garden, undertaking landscaping projects, or dealing with storm damage, this chainsaw delivers efficiency and ease of use, making it a valuable addition to any toolkit.
Top Page Image Contents