Dolmar PE-251 instruction manual Federal Emission Component Defect Warranty

Page 16

EMISSON COMPLIANCE PERIOD

For handheld engine : The Emissions

Compliance Period referred to on the Emissions

Compliance label indicates the number of operating hours for which the engine has been shown to meet Federal emission requirements.

Category C=50 hours, B=125 hours, and A=300 hours.

FEDERAL EMISSION COMPONENT DEFECT WARRANTY

EMISSION COMPONENT DEFECT WARRANTY COVERAGE - This emission warranty is applicable in all States, except the State of California

DOLMAR GmbH North American Division, (herein “Dolmar”) warrant to the initial retail purchaser and each subsequent owner, that this utility equipment engine (herein “engine”) was designed, built, and equipped to conform at the time of initial sale to all applicable regulations of the U.S. Environmental Protection Agency (EPA), and that the engine is free of defects in materials and workmanship which would cause this engine to fall to conform with EPA regulations during its warranty period.

For the components listed under PARTS COVERED, the dealer or service center authorized by Dolmar will, at no cost to you, make the necessary diagnosis, repair, or replacement necessary to ensure that the engine complies with applicable U.S. EPA regulations.

EMISSION COMPONENT DEFECT WARRANTY PERIOD

The warranty period for this engine begins on the date of sale to the initial purchaser and continues for a period of 2 years.

PARTS COVERED

Listed below are the parts covered by the Emission Component Defect Warranty. Some of the parts listed below may require scheduled maintenance and are warranted up to the first scheduled replacement point for that part.

1)

Fuel Metering System

3)

Ignition System

 

(i)

Carburetor and internal parts

 

(i)

Spark plug

 

(ii)

Fuel filter, if applicable

 

(ii)

Flywheel Magneto

 

(iii)

Throttle stopper, if applicable

 

(iii)

Ignition Coil

 

(iv)

Choke System, if applicable

 

 

 

2)

Air Induction System

4)

Miscellaneous Items Used in Above Systems

 

(i)

Air cleaner plate

 

(i)

Fuel hoses, clamps and sealing gaskets

(ii)Air cleaner case

(iii)Air cleaner element

16

Image 16
Contents PE-251 Symbols EnglishSafety Instructions General InstructionsIntended use of the machine Personal protective equipmentRefuelling Maintenance instructions When asking for help, please give the following informationMethod of operation Cutting BladeTechnical Data PE-251 ModelDesignation of Parts Designation of PartsHow to mount the control cable Assembly of Engine and ShaftConnection of the switch cord Mounting of Wheel Mounting of HandleMounting of Deflector Handling fuel FUELS/REFUELLINGFuel and oil mixture Points in Operation and HOW to Stop Correct Handling of MachineAttachment of shoulder strap DetachmentAdjustment of LOW-SPEED Rotation Idling StoppingDaily checkup and maintenance Cleaning of air cleanerServicing Instructions Servicing InstructionsCleaning of muffler exhaust port Checking the spark plugSupply of grease to gear case Supply of grease to flexible shaftFault location Maintenance scheduleStorage Federal Emission Component Defect Warranty Obtaining Warranty Service HOW to Make a Claim Symboles FrançaisConsignes DE Sécurité Instructions généralesUtilisation spéciale de la machine Équipement personnel de protectionRavitaillement MètresInstructions de maintenance Méthode d’utilisationLame de coupe Premier secourCaracteristiques Techniques PE-251 PE-251Nomenclature DES Pièces Assemblage DU Moteur ET DE L’ARBRE Montage du câble de commandeRaccordement de la corde d’interrupteur Montage DU Volant Montage DE LA PoignéeMontage DU Déflecteur CARBURANTS/RAVITAILLEMENT Manipulation Correcte DE LA Machine Consignes DE Mise EN Marche ET Arrêt DE LA MachineFixation du harnais RetraitArrêt Reglage DE LA Marche a Petite Vitesse AU RalentiContrôle et opérations de maintenance réguliers Instructions Relatives AUX RéparationsInstructions Relatives AUX Réparations Nettoyage du filtre à airContôle de la bougie dallumage Graissage du carter de la boîte de vitesseTête daspiration dans le réservoir de carburant Nettoyage de lorifice du pot déchappementRemisage Plan de maintenanceLocalisation des défauts Simbolos Lista de contenidos PáginaInstrucciones DE Seguridad Instrucciones generalesUso recomendado de la máquina Equipo Personal de ProtecciónReabastecimiento Método de trabajo Cuchilla de corteInstrucciones de mantenimiento Nunca rectificar o soldar las herramientas de corte dañadasDatos Técnicos PE-251 ModeloDenominación DE Partes Denominacion DE PartesMontaje del cable de control Montaje DE Motor Y EJEEmpalme del cordón del interruptor Montaje DE LA Rueda Montaje DEL ManillarMontaje DEL Desviador COMBUSTIBLES/REABASTECIMIENTO USO Correcto DE LA Máquina Puntos Relacionados CON EL Manejo Y LA ParadaColocación de la correa para el hombro SeparaciónParo Ajuste DEL Giro a Baja Velocidad RalentíInstrucciones DE Servicio Instrucciones DE ServicioLimpieza del filtro de aire Comprobación de la Bujía Suministro de grasa a la caja de engranajesCabezal de succión en el tanque de combustible Limpieza del orificio de salida del silenciadorAlmacenamiento Page PO Box Alpharetta

PE-251 specifications

The Dolmar PE-251 is a versatile and powerful chainsaw designed for both professional and amateur use. Known for its reliability and robustness, this chainsaw is particularly well-suited for light to medium-duty tasks, making it an excellent choice for homeowners, gardeners, and small-scale forestry operations.

One of the standout features of the Dolmar PE-251 is its lightweight design, which enhances maneuverability and reduces user fatigue. Weighing in at just around 5.5 kg, it enables longer operating periods without compromising performance. The engine, with a displacement of 25.4 cc, delivers a high power-to-weight ratio, ensuring that users can tackle a range of cutting tasks, from trimming branches to felling smaller trees.

The Dolmar PE-251 is equipped with an advanced 2-stroke engine that not only provides exceptional power but also features low emissions, aligning with contemporary environmental standards. This technology ensures that users can work efficiently without contributing excessively to air pollution. The engine operates smoothly, thanks to a well-designed intake and exhaust system that optimizes fuel and air flow.

Another significant characteristic of the PE-251 is its easy-start mechanism, which features a primer bulb and a precision-engineered recoil starter. This technology reduces the effort required for starting the machine, allowing users to get to work quickly. Additionally, the chainsaw incorporates an adjustable oil pump that allows for accurate lubrication of the chain, enhancing performance and prolonging the life of the saw.

Safety is a priority with the Dolmar PE-251, evident in its built-in safety features. The chainsaw includes a chain brake, which can be activated instantly to stop the chain in case of kickback, a common hazard during cutting tasks. Furthermore, the handle is ergonomically designed for a comfortable grip, providing better control and reducing the risk of accidents.

In conclusion, the Dolmar PE-251 is an excellent choice for users seeking a reliable, lightweight chainsaw with innovative features that enhance performance and safety. Whether for maintaining a garden, undertaking landscaping projects, or dealing with storm damage, this chainsaw delivers efficiency and ease of use, making it a valuable addition to any toolkit.