Exmark 4500-507 manual See EXMARK’S Complete Line of Accessories and Options

Page 56

SEE EXMARK’S COMPLETE LINE OF ACCESSORIES AND OPTIONS

MID-MOUNT RIDING ACCESSORIES AND OPTIONS

CUSTOM RIDE SEAT SUSPENSION SYSTEM	OPERATOR CONTROLLED DISCHARGE
FULL SUSPENSION SEAT	ROLL OVER PROTECTION SYSTEM (ROPS)
DECK LIFT ASSIST KIT	SUN SHADE
HITCH KIT	TRASH CONTAINER
LIGHT KIT	TURF STRIPER
12V POWER PORT	ULTRA VAC COLLECTION SYSTEM
MICRO-MULCH SYSTEM	ULTRA VAC QUICK DISPOSAL SYSTEM
OUT-FRONT RIDING ACCESSORIES AND OPTIONS
CUSTOM RIDE SEAT SUSPENSION SYSTEM	SNOW BLADE
DUAL-TAIL WHEEL	SNOWBLOWER
FLOOR PAN EXTENDER	SUN SHADE
HITCH KIT	TRASH CONTAINER
LIGHT KIT	ULTRA VAC COLLECTION SYSTEM
MICRO-MULCH SYSTEM	ULTRA VAC QUICK DISPOSAL SYSTEM
ROLL OVER PROTECTION SYSTEM (ROPS)	WEATHER CAB

WALK-BEHIND ACCESSORIES AND OPTIONS

GRASS CATCHER

MICRO-MULCH SYSTEM

Place Model No. and Serial No.

Label Here (Included in the Literature

Pack) or Fill in Below

Model No.

Serial No.

TURF STRIPER

STANDON

Date Purchased

Engine Model No. and Spec. No.

Engine Serial No. (E/No)

© 2009 Exmark Mfg. Co., Inc.	Part No. 4500-507 Rev. B
Industrial Park Box 808	(402) 223-6300
Beatrice, NE 68310	Fax (402) 223-5489
All Rights Reserved	Printed in the USA

www.exmark.com

Image 56

Contents Lazer Z Models California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 117-2718 116-0211 Message Display Systems SpecificationsModel Numbers Tires & Wheels SeatHydrostatic Ground Drive System Dimensions Cutting DeckOverall Width Overall LengthCurb Weight Accessory Weight Table WorksheetTread Width Center to Center of Tires, Widthwise Wheel Base Center of Caster Tire to Center of Drive TireProduct Overview Torque RequirementsOperation ControlsIgnition Switch Hour MeterFuel Shut-Off Valve Fuel GaugePTO Engagement Switch Low Voltage IndicatorDrive Wheel Release Valves Deck Lift PedalRaise the Rollover Protection System Rops Pre-StartOperating Instructions Open the Fuel Shut-Off Valve Starting the EngineEngaging the PTO Disengaging the PTOAdjusting the Cutting Height Driving the MachineTransporting a Unit Adjusting the Anti-Scalp RollersTransporting Loading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelCheck Safety Interlock System Check Mower BladesService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareCheck Tire Pressures Change Engine OilCheck Hydraulic Oil Level Lubricate Caster Wheel Hubs Check Condition Of BeltsLubricate Grease Fittings Lubricate Brake Handle Pivot Lubricate Deck Lift PivotCheck Spark Plugs Change Fuel FilterWheel Hub Slotted Nut Torque Specification Check Spark Arrester if equippedThread Locking Adhesives Copper-Based Anti-seizeDielectric Grease Deck LevelingFoot lever Transport lock Cut of height pin Deck Removal Deck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Electric Clutch Adjustment Motion Control Linkage AdjustmentMotion Control Damper Adjustment RH Motion Control ShownMotion Control Neutral Lock Pivot Adjustment Motion Control Handle AdjustmentCaster Pivot Bearings Pre-Load Adjustment Clutch ShimShim Clean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsClean Hydro Fan Cooling Guards Clean Debris From MachineMotor Oil Disposal Battery DisposalWaste Disposal Troubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics Electrical DiagramSchematic ElectricalHydraulic Diagram Exmark Lazer Z and Lazer Z AS Turf Equipment Page Page See EXMARK’S Complete Line of Accessories and Options