Exmark 4500-466 manual Open the Fuel Shut-Off Valve, Starting the Engine

Page 23

Operation

2.Apply forward pressure to the upper hoop of the roll bar.

3. Pull the knob and rotate 90° to hold in the unlatched position to lower the roll bar.

4. To return to the operate position, raise the roll bar, and then rotate knobs 90° so that the tabs interlock partially. Apply forward pressure to the roll bar upper hoop and observe that the knobs return to the completely latched position.

1. Engaged

Figure 14

2.Partially engaged — Do Not operate with ROPS in this condition.

Figure 13

1.Roll bar upper hoop

2.Knob in “latched” position

3.Pull knob to unlatch

4.Rotate 90° to hold unlatched

5.Knob in “unlatched” position

5.Make sure the knobs are fully engaged with the roll bar in the raised position. The upper hoop of the roll bar may need to be pushed forward or pulled rearward to get both knobs fully engaged (see Figure 14).

Important: Always use the seat belt with the roll bar in the operate (raised) position. Ensure that the rear part of the seat is secured with the seat latch.

Open the Fuel Shut-Off Valve

The fuel shut off valve is located behind and below the seat. Rotate the valve and align with the fuel line to open.

Starting the Engine

1.Move the motion control levers out to the neutral lock position.

2.Pull up and back on the parking brake lever to engage the parking brake.

3.Push down on the PTO switch to the “disengage” position.

Note: It is not necessary for the operator to be in the seat to start the engine.

4.Place the throttle midway between the “SLOW” and “FAST” positions.

5.On a cold engine, push the choke lever forward into the “ON” position.

On a warm engine, leave the choke in the “OFF” position.

6.Turn ignition switch to the “START” position. Release the switch as soon as the engine starts.

Important: Do Not crank the engine continuously for more than ten seconds at a time. If the engine does not start, allow a 60 second cool-down period between starting

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Lazer Z Advantage Series Models California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0211 Systems SpecificationsModel Numbers Tires & Wheels Operator ControlsSeat Hydrostatic Ground Drive SystemOverall Height DimensionsOverall Width Overall LengthWheel Base Center of Caster Tire to Center of Drive Tire Curb WeightAccessory Weight Table Worksheet Tread Width Center to Center of Tires, WidthwiseTorque Requirements Product OverviewControls OperationHour Meter Ignition SwitchFuel Gauge PTO Engagement SwitchLow Voltage Indicator Fuel Shut-Off ValveTransport Lock Pre-StartOperating Instructions Deck Lift PedalStarting the Engine Open the Fuel Shut-Off ValveDriving the Machine Engaging the PTODisengaging the PTO Stopping the EngineDriving Forward Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Loading a Unit TransportingTransporting a Unit Operation Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeCheck Mower Blades Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltCheck Hydraulic Oil Level Change Engine OilLubricate Caster Wheel Hubs Check Tire PressuresCheck Condition Of Belts Lubricate Grease FittingsChange Fuel Filter Lubricate Brake Handle PivotLubricate Deck Lift Pivot Check Spark PlugsWheel Hub Slotted Nut Torque Specification Change Engine Coolant Kawasaki Liquid-Cooled Only Check Engine Coolant Level Kawasaki Liquid-Cooled OnlyDielectric Grease Check Spark Arrester if equippedThread Locking Adhesives Copper-Based Anti-seizeDeck Leveling AdjustmentsRe-tighten front and rear height-of-cut plate mounting bolts Deck Belt Tension Adjusting the Parking BrakeDeck Removal Pump Drive Belt TensionMotion Control Linkage Adjustment Electric Clutch AdjustmentMotion Control Neutral Lock Pivot Adjustment Motion Control Damper AdjustmentCaster Pivot Bearings Pre-Load Adjustment Motion Control Handle AdjustmentClean Hydro Fan Cooling Guards Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Waste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Battery DisposalProblem Possible Cause Corrective Action TroubleshootingRefer to Check Engine Coolant Level Electrical Diagram Air-Cooled SchematicsTAN Electrical Diagram Liquid-CooledElectrical Logic Schematic Air-Cooled Schematics Hydraulic Diagram Exmark Lazer Z and Lazer Z AS Turf Equipment Page Page Service Record Page Page See EXMARK’S Complete Line of Accessories and Options

4500-466 specifications

The Exmark 4500-466 is a cutting-edge zero-turn mower designed for those who demand precision, reliability, and efficiency in their lawn care routines. As part of Exmark's celebrated lineup, the 4500-466 delivers exceptional performance and versatility, making it an ideal choice for both residential and commercial users.

One of the standout features of the Exmark 4500-466 is its robust engine. Equipped with a powerful engine that boasts a high horsepower rating, this mower can tackle even the toughest of mowing conditions. The engine is engineered for optimal efficiency and longevity, ensuring that users can rely on it for many seasons of dependable service.

The Exmark 4500-466 also incorporates innovative cutting technologies that set it apart from traditional mowers. Its patented UltraCut deck technology provides a superior cut quality, allowing for precise trimming of grass, ensuring an even and professional-looking lawn. The 60-inch cutting width enables users to cover larger areas in less time while still maintaining a clean cut.

Comfort and usability are additionally prioritized in the design of the Exmark 4500-466. The ergonomic controls and adjustable seat provide operators with a comfortable mowing experience. The reduced vibration and improved suspension system offer a smooth ride, even over uneven terrain. This attention to user comfort is essential, especially for those who spend extended periods mowing.

Another significant feature is the machine's advanced drive mechanics. The dual hydrostatic drive system ensures smooth handling and intuitive control, making it easy to maneuver around obstacles and tight spaces. The zero-turn capability allows for precise navigation and enhances productivity, significantly reducing mowing time.

In terms of durability, the Exmark 4500-466 is built to withstand the rigors of frequent use. The heavy-duty frame and high-quality materials ensure that the mower can endure tough conditions while maintaining its performance. Regular maintenance is made easy through accessible components, ensuring owners can keep their mower in top condition with minimal effort.

In conclusion, the Exmark 4500-466 represents the pinnacle of zero-turn mower technology. With its powerful engine, advanced cutting systems, user-centric design, and robust construction, it offers everything needed for effective lawn care. Whether you're a professional landscaper or a homeowner looking for a reliable mowing solution, the Exmark 4500-466 is a worthy investment that will exceed expectations.
Top Page Image Contents