Exmark 4500-466 manual Slope Operation, Using the Rollover Protection System Rops

Page 8

Safety

Be aware of the mower discharge path and direct discharge away from others.

Do Not operate the mower under the influence of alcohol or drugs.

Use extreme care when loading or unloading the machine into a trailer or truck.

Use care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

Slope Operation

Use Extreme caution when mowing and/or turning on slopes as loss of traction and/or tip-over could occur. The operator is responsible for safe operation on slopes.

DANGER

Operating on wet grass or steep slopes can cause sliding and loss of control. Wheels dropping over edges, ditches, steep banks, or water can cause rollovers, which may result in serious injury, death or drowning.

Do Not mow slopes when grass is wet.

Do Not mow near drop-offs or near water.

Do Not mow slopes greater than 15 degrees.

Reduce speed and use extreme caution on slopes.

Avoid sudden turns or rapid speed changes.

Keep the roll bar in the raised and locked position and use seat belt.

See inside the back cover to determine the approximate slope angle of the area to be mowed.

Use a walk behind mower and/or a hand trimmer near drop-offs, ditches, steep banks or water. (Figure 3).

Figure 3

1.Safe Zone-Use the mower here on slopes less than 15 degrees

2.Danger Zone-Use a walk behind mower and/or hand trimmer on slopes greater than 15 degrees, near drop-offs and water.

3.Water

Remove or mark obstacles such as rocks, tree limbs, etc. from the mowing area. Tall grass can hide obstacles.

Watch for ditches, holes, rocks, dips and rises that change the operating angle, as rough terrain could overturn the machine.

Avoid sudden starts when mowing uphill because the mower may tip backwards.

Be aware that operating on wet grass, across steep slopes or down hill may cause the mower to lose traction. Loss of traction to the drive wheels may result in sliding and loss of braking and steering.

Always avoid sudden starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly off the slope.

Follow the manufacturer’s recommendations for wheel weights or counter weights to improve stability.

Use extreme care with grass catchers or attachments. These can change the stability of the machine and cause loss of control.

Using the Rollover Protection System (ROPS)

A Rollover Protection System (roll bar) is installed on the unit.

8

Image 8
Contents Lazer Z Advantage Series Models California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0211 Systems SpecificationsModel Numbers Operator Controls SeatHydrostatic Ground Drive System Tires & WheelsDimensions Overall WidthOverall Length Overall HeightCurb Weight Accessory Weight Table WorksheetTread Width Center to Center of Tires, Widthwise Wheel Base Center of Caster Tire to Center of Drive TireProduct Overview Torque RequirementsOperation ControlsIgnition Switch Hour MeterPTO Engagement Switch Low Voltage IndicatorFuel Shut-Off Valve Fuel GaugePre-Start Operating InstructionsDeck Lift Pedal Transport LockOpen the Fuel Shut-Off Valve Starting the EngineEngaging the PTO Disengaging the PTOStopping the Engine Driving the MachineAdjusting the Cutting Height Driving ForwardAdjusting the Anti-Scalp Rollers Loading a Unit TransportingTransporting a Unit Operation Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelCheck Safety Interlock System Check Mower BladesService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Brake Handle Pivot Lubricate Deck Lift PivotCheck Spark Plugs Change Fuel FilterWheel Hub Slotted Nut Torque Specification Check Engine Coolant Level Kawasaki Liquid-Cooled Only Change Engine Coolant Kawasaki Liquid-Cooled OnlyCheck Spark Arrester if equipped Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseAdjustments Deck LevelingRe-tighten front and rear height-of-cut plate mounting bolts Adjusting the Parking Brake Deck RemovalPump Drive Belt Tension Deck Belt TensionElectric Clutch Adjustment Motion Control Linkage AdjustmentMotion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean Hydro Fan Cooling Guards Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From Machine Clean Grass Build-Up Under DeckBattery Disposal Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionRefer to Check Engine Coolant Level Schematics Electrical Diagram Air-CooledElectrical Diagram Liquid-Cooled TANElectrical Logic Schematic Air-Cooled Schematics Hydraulic Diagram Exmark Lazer Z and Lazer Z AS Turf Equipment Page Page Service Record Page Page See EXMARK’S Complete Line of Accessories and Options

4500-466 specifications

The Exmark 4500-466 is a cutting-edge zero-turn mower designed for those who demand precision, reliability, and efficiency in their lawn care routines. As part of Exmark's celebrated lineup, the 4500-466 delivers exceptional performance and versatility, making it an ideal choice for both residential and commercial users.

One of the standout features of the Exmark 4500-466 is its robust engine. Equipped with a powerful engine that boasts a high horsepower rating, this mower can tackle even the toughest of mowing conditions. The engine is engineered for optimal efficiency and longevity, ensuring that users can rely on it for many seasons of dependable service.

The Exmark 4500-466 also incorporates innovative cutting technologies that set it apart from traditional mowers. Its patented UltraCut deck technology provides a superior cut quality, allowing for precise trimming of grass, ensuring an even and professional-looking lawn. The 60-inch cutting width enables users to cover larger areas in less time while still maintaining a clean cut.

Comfort and usability are additionally prioritized in the design of the Exmark 4500-466. The ergonomic controls and adjustable seat provide operators with a comfortable mowing experience. The reduced vibration and improved suspension system offer a smooth ride, even over uneven terrain. This attention to user comfort is essential, especially for those who spend extended periods mowing.

Another significant feature is the machine's advanced drive mechanics. The dual hydrostatic drive system ensures smooth handling and intuitive control, making it easy to maneuver around obstacles and tight spaces. The zero-turn capability allows for precise navigation and enhances productivity, significantly reducing mowing time.

In terms of durability, the Exmark 4500-466 is built to withstand the rigors of frequent use. The heavy-duty frame and high-quality materials ensure that the mower can endure tough conditions while maintaining its performance. Regular maintenance is made easy through accessible components, ensuring owners can keep their mower in top condition with minimal effort.

In conclusion, the Exmark 4500-466 represents the pinnacle of zero-turn mower technology. With its powerful engine, advanced cutting systems, user-centric design, and robust construction, it offers everything needed for effective lawn care. Whether you're a professional landscaper or a homeowner looking for a reliable mowing solution, the Exmark 4500-466 is a worthy investment that will exceed expectations.