Exmark 4500-466 manual Troubleshooting, Problem Possible Cause Corrective Action

Page 47

Troubleshooting

Troubleshooting

Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mower use.

When a problem occurs, do not overlook the simple causes. For example: starting problems could be caused by an empty fuel tank.

The following table lists some of the common causes of trouble. Do not attempt to service or replace major items or any items that call for special timing of adjustment procedures (such as valves, governor, etc.). Have this work done by your Engine Service Dealer.

Note: When disconnecting electrical connectors DO NOT pull on the wires to separate the connectors.

Problem

 

Possible Cause

 

Corrective Action

 

 

 

 

 

Starter does not crank

1.

PTO is engaged.

1.

Disengage the PTO.

 

2.

Parking brake is not engaged.

2.

Set the parking brake.

 

3.

Drive levers are not in neutral lock

3.

Ensure the drive levers are in the neutral

 

 

position.

 

lock position.

 

4.

Battery does not have a full charge.

4.

Charge the battery.

 

5.

Electrical connections are corroded, loose

5.

Check the electrical connections for

 

 

or faulty.

 

good contact. Clean connector terminals

 

 

 

 

thoroughly with electrical contact cleaner,

 

 

 

 

apply dielectric grease and reconnect.

 

6.

Fuse is blown.

6.

Replace the blown fuse.

 

7.

Relay or switch is defective.

7.

Contact an Authorized Service Dealer.

 

8.

Faulty module.

8.

Replace module.

 

 

 

 

 

Engine will not start, starts hard, or fails to

1.

Fuel tank is empty.

1.

Fill the fuel tank.

keep running

2.

Fuel shutoff valve is closed.

2.

Open the fuel shutoff valve.

 

 

3.

Oil level in the crankcase is low.

3.

Add oil to the crankcase.

 

4.

The throttle and choke are not in the

4.

Be sure the throttle control is midway

 

 

correct position.

 

between the “SLOW” and “FAST”

 

 

 

 

positions, and the choke is in the “ON”

 

 

 

 

position for a cold engine or the “OFF”

 

 

 

 

position for a warm engine.

 

5.

Dirt in fuel filter.

5.

Replace the fuel filter.

 

6.

Dirt, water, or stale fuel is in the fuel

6.

Contact an Authorized Service Dealer.

 

 

system.

 

 

 

7.

Air cleaner is dirty.

7.

Clean or replace the air cleaner element.

 

8.

Seat switch is not functioning properly.

8.

Check the seat switch indicator. Replace

 

 

 

 

seat if needed.

 

9.

Electrical connections are corroded, loose

9.

Check the electrical connections for

 

 

or faulty.

 

good contact. Clean connector terminals

 

 

 

 

thoroughly with electrical contact cleaner,

 

 

 

 

apply dielectric grease and reconnect.

 

10.

Relay or switch is defective.

10.

Contact an Authorized Service Dealer.

 

11.

Faulty spark plug.

11.

Clean, adjust or replace spark plug.

 

12.

Spark plug wire is not connected.

12.

Check the spark plug wire connection.

 

13.

Faulty module.

13.

Replace module.

 

 

 

 

 

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Lazer Z Advantage Series Models California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0211 Systems SpecificationsModel Numbers Tires & Wheels Operator ControlsSeat Hydrostatic Ground Drive SystemOverall Height DimensionsOverall Width Overall LengthWheel Base Center of Caster Tire to Center of Drive Tire Curb WeightAccessory Weight Table Worksheet Tread Width Center to Center of Tires, WidthwiseTorque Requirements Product OverviewControls OperationHour Meter Ignition SwitchFuel Gauge PTO Engagement SwitchLow Voltage Indicator Fuel Shut-Off ValveTransport Lock Pre-StartOperating Instructions Deck Lift PedalStarting the Engine Open the Fuel Shut-Off ValveDriving the Machine Engaging the PTODisengaging the PTO Stopping the EngineDriving Forward Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Loading a Unit TransportingTransporting a Unit Operation Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeCheck Mower Blades Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltCheck Hydraulic Oil Level Change Engine OilLubricate Caster Wheel Hubs Check Tire PressuresCheck Condition Of Belts Lubricate Grease FittingsChange Fuel Filter Lubricate Brake Handle PivotLubricate Deck Lift Pivot Check Spark PlugsWheel Hub Slotted Nut Torque Specification Change Engine Coolant Kawasaki Liquid-Cooled Only Check Engine Coolant Level Kawasaki Liquid-Cooled OnlyDielectric Grease Check Spark Arrester if equippedThread Locking Adhesives Copper-Based Anti-seizeDeck Leveling AdjustmentsRe-tighten front and rear height-of-cut plate mounting bolts Deck Belt Tension Adjusting the Parking BrakeDeck Removal Pump Drive Belt TensionMotion Control Linkage Adjustment Electric Clutch AdjustmentMotion Control Neutral Lock Pivot Adjustment Motion Control Damper AdjustmentCaster Pivot Bearings Pre-Load Adjustment Motion Control Handle AdjustmentClean Hydro Fan Cooling Guards Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Waste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Battery DisposalProblem Possible Cause Corrective Action TroubleshootingRefer to Check Engine Coolant Level Electrical Diagram Air-Cooled SchematicsTAN Electrical Diagram Liquid-CooledElectrical Logic Schematic Air-Cooled Schematics Hydraulic Diagram Exmark Lazer Z and Lazer Z AS Turf Equipment Page Page Service Record Page Page See EXMARK’S Complete Line of Accessories and Options

4500-466 specifications

The Exmark 4500-466 is a cutting-edge zero-turn mower designed for those who demand precision, reliability, and efficiency in their lawn care routines. As part of Exmark's celebrated lineup, the 4500-466 delivers exceptional performance and versatility, making it an ideal choice for both residential and commercial users.

One of the standout features of the Exmark 4500-466 is its robust engine. Equipped with a powerful engine that boasts a high horsepower rating, this mower can tackle even the toughest of mowing conditions. The engine is engineered for optimal efficiency and longevity, ensuring that users can rely on it for many seasons of dependable service.

The Exmark 4500-466 also incorporates innovative cutting technologies that set it apart from traditional mowers. Its patented UltraCut deck technology provides a superior cut quality, allowing for precise trimming of grass, ensuring an even and professional-looking lawn. The 60-inch cutting width enables users to cover larger areas in less time while still maintaining a clean cut.

Comfort and usability are additionally prioritized in the design of the Exmark 4500-466. The ergonomic controls and adjustable seat provide operators with a comfortable mowing experience. The reduced vibration and improved suspension system offer a smooth ride, even over uneven terrain. This attention to user comfort is essential, especially for those who spend extended periods mowing.

Another significant feature is the machine's advanced drive mechanics. The dual hydrostatic drive system ensures smooth handling and intuitive control, making it easy to maneuver around obstacles and tight spaces. The zero-turn capability allows for precise navigation and enhances productivity, significantly reducing mowing time.

In terms of durability, the Exmark 4500-466 is built to withstand the rigors of frequent use. The heavy-duty frame and high-quality materials ensure that the mower can endure tough conditions while maintaining its performance. Regular maintenance is made easy through accessible components, ensuring owners can keep their mower in top condition with minimal effort.

In conclusion, the Exmark 4500-466 represents the pinnacle of zero-turn mower technology. With its powerful engine, advanced cutting systems, user-centric design, and robust construction, it offers everything needed for effective lawn care. Whether you're a professional landscaper or a homeowner looking for a reliable mowing solution, the Exmark 4500-466 is a worthy investment that will exceed expectations.
Top Page Image Contents