Exmark 4500-466 manual Waste Disposal, Clean Debris From Machine, Clean Grass Build-Up Under Deck

Page 46

Maintenance

Removing debris from the hydro fan cooling guards will allow the hydro system to run cooler and improve the life of the hydro system.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Slide seat all the way back, then lift the seat to access the LH and RH hydro drive area.

3.Remove accumulated debris from the hydro fan cooling guards.

Waste Disposal

Motor Oil Disposal

Engine oil and hydraulic oil are both pollutants to the environment. Dispose of used oil at a certified recycling center or according to your state and local regulations.

Battery Disposal

Clean Debris From Machine

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Clean off any oil, debris, or grass build-up on the machine and cutting deck, especially under deck belt shields, around the fuel tank, around engine and exhaust area.

Clean Grass Build-Up Under Deck

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Raise deck to the transport (5 1/2 inch (14 cm) cutting height) position. Lift the front of unit and support unit using jack stands or equivalent support.

CAUTION

Raising the mower deck for service or maintenance relying solely on mechanical or hydraulic jacks could be dangerous. The mechanical or hydraulic jacks may not be enough support or may malfunction allowing the unit to fall, which could cause injury.

Do Not rely solely on mechanical or hydraulic jacks for support. Use adequate jack stands or equivalent support.

3.Clean out any grass build-up from underside of deck and in discharge deflector.

DANGER

Battery electrolyte contains sulfuric acid, which is poisonous and can cause severe burns. Swallowing electrolyte can be fatal or if it touches skin can cause severe burns.

•Wear safety glasses to shield eyes, and rubber gloves to protect skin and clothing when handling electrolyte.

•Do Not swallow electrolyte.

Federal law states that batteries should not be placed in the garbage. Management and disposal practices must be within relevant federal, state, or local laws.

If a battery is being replaced or if the unit containing the battery is no longer operating and is being scrapped, take the battery to a local certified recycling center. If no local recycling is available return the battery to any certified battery reseller.

46

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Lazer Z Advantage Series Models California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0211 Model Numbers SpecificationsSystems Hydrostatic Ground Drive System Operator ControlsSeat Tires & WheelsOverall Length DimensionsOverall Width Overall HeightTread Width Center to Center of Tires, Widthwise Curb WeightAccessory Weight Table Worksheet Wheel Base Center of Caster Tire to Center of Drive TireProduct Overview Torque RequirementsOperation ControlsIgnition Switch Hour MeterFuel Shut-Off Valve PTO Engagement SwitchLow Voltage Indicator Fuel GaugeDeck Lift Pedal Pre-StartOperating Instructions Transport LockOpen the Fuel Shut-Off Valve Starting the EngineStopping the Engine Engaging the PTODisengaging the PTO Driving the MachineAdjusting the Cutting Height Driving ForwardAdjusting the Anti-Scalp Rollers Transporting a Unit TransportingLoading a Unit Operation Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelCheck Safety Interlock System Check Mower BladesCheck Seat Belt Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelLubricate Grease Fittings Check Tire PressuresCheck Condition Of Belts Lubricate Caster Wheel HubsCheck Spark Plugs Lubricate Brake Handle PivotLubricate Deck Lift Pivot Change Fuel FilterWheel Hub Slotted Nut Torque Specification Check Engine Coolant Level Kawasaki Liquid-Cooled Only Change Engine Coolant Kawasaki Liquid-Cooled OnlyCopper-Based Anti-seize Check Spark Arrester if equippedThread Locking Adhesives Dielectric GreaseAdjustments Deck LevelingRe-tighten front and rear height-of-cut plate mounting bolts Pump Drive Belt Tension Adjusting the Parking BrakeDeck Removal Deck Belt TensionElectric Clutch Adjustment Motion Control Linkage AdjustmentMotion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Caster Pivot Bearings Pre-Load AdjustmentRemove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Guards Battery Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionRefer to Check Engine Coolant Level Schematics Electrical Diagram Air-CooledElectrical Diagram Liquid-Cooled TANElectrical Logic Schematic Air-Cooled Schematics Hydraulic Diagram Exmark Lazer Z and Lazer Z AS Turf Equipment Page Page Service Record Page Page See EXMARK’S Complete Line of Accessories and Options

4500-466 specifications

The Exmark 4500-466 is a cutting-edge zero-turn mower designed for those who demand precision, reliability, and efficiency in their lawn care routines. As part of Exmark's celebrated lineup, the 4500-466 delivers exceptional performance and versatility, making it an ideal choice for both residential and commercial users.

One of the standout features of the Exmark 4500-466 is its robust engine. Equipped with a powerful engine that boasts a high horsepower rating, this mower can tackle even the toughest of mowing conditions. The engine is engineered for optimal efficiency and longevity, ensuring that users can rely on it for many seasons of dependable service.

The Exmark 4500-466 also incorporates innovative cutting technologies that set it apart from traditional mowers. Its patented UltraCut deck technology provides a superior cut quality, allowing for precise trimming of grass, ensuring an even and professional-looking lawn. The 60-inch cutting width enables users to cover larger areas in less time while still maintaining a clean cut.

Comfort and usability are additionally prioritized in the design of the Exmark 4500-466. The ergonomic controls and adjustable seat provide operators with a comfortable mowing experience. The reduced vibration and improved suspension system offer a smooth ride, even over uneven terrain. This attention to user comfort is essential, especially for those who spend extended periods mowing.

Another significant feature is the machine's advanced drive mechanics. The dual hydrostatic drive system ensures smooth handling and intuitive control, making it easy to maneuver around obstacles and tight spaces. The zero-turn capability allows for precise navigation and enhances productivity, significantly reducing mowing time.

In terms of durability, the Exmark 4500-466 is built to withstand the rigors of frequent use. The heavy-duty frame and high-quality materials ensure that the mower can endure tough conditions while maintaining its performance. Regular maintenance is made easy through accessible components, ensuring owners can keep their mower in top condition with minimal effort.

In conclusion, the Exmark 4500-466 represents the pinnacle of zero-turn mower technology. With its powerful engine, advanced cutting systems, user-centric design, and robust construction, it offers everything needed for effective lawn care. Whether you're a professional landscaper or a homeowner looking for a reliable mowing solution, the Exmark 4500-466 is a worthy investment that will exceed expectations.
Top Page Image Contents