Electric Clutch Adjustment

Exmark 4500-466 manual Electric Clutch Adjustment, Motion Control Linkage Adjustment

Maintenance

Figure 32

Left Hand Brake Shown

1.	Cable anchor	6.	Lock nut
2.	Threaded rod	7.	Pull cable threaded rod
			this direction
3.	Push lever this direction	8.	Hold threaded rod here
4.	Caliper lever arm	9.	Swivel (pivot head)

5.Standard nut (shown against swivel)

Note the order of the standard nut and lock nut (no nut on the cable anchor side of the swivel).

10.Release hold on the caliper lever and cable. The wheel hub should turn by hand in both directions relative to the caliper; some friction/resistance is acceptable.

11.If there is no movement between the hub rotor and the caliper then back off the standard nut one turn from the swivel and repeat step 10 (drive release valves must be in the “released” position on the hydros).

12.If the hub rotor moves very freely relative to the caliper, then tighten the standard nut one turn against the swivel and repeat step 10.

13.Once step 10 is achieved, hold the threaded rod end with a tool and tighten the lock nut against the standard nut. Do Not allow the cable to turn when the nuts are tightened.

14.Rotate the drive wheel release handle to the “operating” position. Refer to the Drive Wheel Release Valves section in Operation.

15.Repeat on the opposite side of machine.

16.Install the rear tires and torque lug nuts to 90-95 ft-lb (122-129 N-m).

17.Remove jack stands.

No adjustment necessary.

Motion Control Linkage Adjustment

Located on either side of the fuel tank, below the seat are the pump control linkages. Rotating the pump linkage with a 1/2 inch wrench allows fine tuning adjustments so that the machine does not move in neutral. Any adjustments should be made for neutral positioning only.

WARNING

Engine must be running and drive wheels must be turning so motion control adjustment can be performed. Contact with moving parts or hot surfaces may cause personal injury.

Keep fingers, hands, and clothing clear of rotating components and hot surfaces.

1.Prior to starting the engine, push the deck lift pedal and remove the height of cut pin. Lower deck to the ground.

2.Raise the rear of machine up and support with jack stands (or equivalent support) just high enough to allow drive wheels to turn freely.

3.Remove the electrical connection from the seat safety switch, located under the bottom cushion of the seat. The switch is a part of the seat assembly.

4.Temporarily install a jumper wire across the terminals in the connector of the main wiring harness.

5.Start engine. Brake must be engaged and motion control levers out to start engine. Operator does not have to be in the seat because of the jumper wire being used. Run engine at full throttle and release brake.

6.Run the unit at least 5 minutes with the drive levers at full forward speed to bring hydraulic oil up to operating temperature.

4500-466 specifications

The Exmark 4500-466 is a cutting-edge zero-turn mower designed for those who demand precision, reliability, and efficiency in their lawn care routines. As part of Exmark's celebrated lineup, the 4500-466 delivers exceptional performance and versatility, making it an ideal choice for both residential and commercial users.

One of the standout features of the Exmark 4500-466 is its robust engine. Equipped with a powerful engine that boasts a high horsepower rating, this mower can tackle even the toughest of mowing conditions. The engine is engineered for optimal efficiency and longevity, ensuring that users can rely on it for many seasons of dependable service.

The Exmark 4500-466 also incorporates innovative cutting technologies that set it apart from traditional mowers. Its patented UltraCut deck technology provides a superior cut quality, allowing for precise trimming of grass, ensuring an even and professional-looking lawn. The 60-inch cutting width enables users to cover larger areas in less time while still maintaining a clean cut.

Comfort and usability are additionally prioritized in the design of the Exmark 4500-466. The ergonomic controls and adjustable seat provide operators with a comfortable mowing experience. The reduced vibration and improved suspension system offer a smooth ride, even over uneven terrain. This attention to user comfort is essential, especially for those who spend extended periods mowing.

Another significant feature is the machine's advanced drive mechanics. The dual hydrostatic drive system ensures smooth handling and intuitive control, making it easy to maneuver around obstacles and tight spaces. The zero-turn capability allows for precise navigation and enhances productivity, significantly reducing mowing time.

In terms of durability, the Exmark 4500-466 is built to withstand the rigors of frequent use. The heavy-duty frame and high-quality materials ensure that the mower can endure tough conditions while maintaining its performance. Regular maintenance is made easy through accessible components, ensuring owners can keep their mower in top condition with minimal effort.

In conclusion, the Exmark 4500-466 represents the pinnacle of zero-turn mower technology. With its powerful engine, advanced cutting systems, user-centric design, and robust construction, it offers everything needed for effective lawn care. Whether you're a professional landscaper or a homeowner looking for a reliable mowing solution, the Exmark 4500-466 is a worthy investment that will exceed expectations.