Exmark 4500-466 manual Re-tighten front and rear height-of-cut plate mounting bolts

Page 40

Maintenance

12. Re-measure until all four sides are the correct height. Tighten all the nuts on the deck lift arm assemblies.

13. Lower discharge deflector.

14. If the four deck links do not have enough adjustment to achieve accurate cut height with the desired rake, the single point adjustment can be utilized to gain more adjustment (see Figure 30).

Figure 28

1.

3 1/4 inches (8.3 cm)

4.

3 inches (7.6 cm)

2.

Back blade tip

5.

Level surface

3.Front blade tip

10.Loosen the whizlock nut on the side of the yoke and the jam nut on top. Fine tune the screw adjuster by turning it to get 3 inch (7.6 mm) height (see Figure 29).

To increase the height, turn the adjuster screw clockwise; to decrease, turn counterclockwise.

 

 

Figure 29

 

1.

Whizlock nut

3.

Jam nut

2.

Adjuster screw

4.

Yoke

11.The back tips of the side blades should measure 3 1/4 inches (8.3 cm). Fine tune rear adjusters as required.

Figure 30

1.Single point height adjustment bolt

2.Front height-of-cut plate mounting bolt

3.Rear height-of-cut plate mounting bolt

15.To adjust the single point system, first loosen the front and rear height-of-cut plate mounting bolts.

16.If the deck is too low, tighten the single point adjustment bolt by rotating it clockwise. If the deck is too high, loosen the single point adjustment bolt by rotating it counterclockwise.

Note: Loosen or tighten the single point adjustment bolt enough to move the height-of-cut plate mounting bolts at least 1/3 the length of the available travel in their slots. This will regain some up and down adjustment on each of the four deck links.

17.Re-tighten front and rear height-of-cut plate mounting bolts.

Important: Torque the front and rear height-of-cut plate mounting bolts to 27-33 ft-lb (37-45 N-m).

18.Repeat steps 9 through 13.

40

Image 40
Contents Lazer Z Advantage Series Models California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0211 Model Numbers SpecificationsSystems Operator Controls SeatHydrostatic Ground Drive System Tires & WheelsDimensions Overall WidthOverall Length Overall HeightCurb Weight Accessory Weight Table WorksheetTread Width Center to Center of Tires, Widthwise Wheel Base Center of Caster Tire to Center of Drive TireProduct Overview Torque RequirementsOperation ControlsIgnition Switch Hour MeterPTO Engagement Switch Low Voltage IndicatorFuel Shut-Off Valve Fuel GaugePre-Start Operating InstructionsDeck Lift Pedal Transport LockOpen the Fuel Shut-Off Valve Starting the EngineEngaging the PTO Disengaging the PTOStopping the Engine Driving the MachineAdjusting the Cutting Height Driving ForwardAdjusting the Anti-Scalp Rollers Transporting a Unit TransportingLoading a Unit Operation Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelCheck Safety Interlock System Check Mower BladesService Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Brake Handle Pivot Lubricate Deck Lift PivotCheck Spark Plugs Change Fuel FilterWheel Hub Slotted Nut Torque Specification Check Engine Coolant Level Kawasaki Liquid-Cooled Only Change Engine Coolant Kawasaki Liquid-Cooled OnlyCheck Spark Arrester if equipped Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseAdjustments Deck LevelingRe-tighten front and rear height-of-cut plate mounting bolts Adjusting the Parking Brake Deck RemovalPump Drive Belt Tension Deck Belt TensionElectric Clutch Adjustment Motion Control Linkage AdjustmentMotion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Caster Pivot Bearings Pre-Load AdjustmentRemove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Guards Clean Debris From Machine Clean Grass Build-Up Under DeckBattery Disposal Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionRefer to Check Engine Coolant Level Schematics Electrical Diagram Air-CooledElectrical Diagram Liquid-Cooled TANElectrical Logic Schematic Air-Cooled Schematics Hydraulic Diagram Exmark Lazer Z and Lazer Z AS Turf Equipment Page Page Service Record Page Page See EXMARK’S Complete Line of Accessories and Options

4500-466 specifications

The Exmark 4500-466 is a cutting-edge zero-turn mower designed for those who demand precision, reliability, and efficiency in their lawn care routines. As part of Exmark's celebrated lineup, the 4500-466 delivers exceptional performance and versatility, making it an ideal choice for both residential and commercial users.

One of the standout features of the Exmark 4500-466 is its robust engine. Equipped with a powerful engine that boasts a high horsepower rating, this mower can tackle even the toughest of mowing conditions. The engine is engineered for optimal efficiency and longevity, ensuring that users can rely on it for many seasons of dependable service.

The Exmark 4500-466 also incorporates innovative cutting technologies that set it apart from traditional mowers. Its patented UltraCut deck technology provides a superior cut quality, allowing for precise trimming of grass, ensuring an even and professional-looking lawn. The 60-inch cutting width enables users to cover larger areas in less time while still maintaining a clean cut.

Comfort and usability are additionally prioritized in the design of the Exmark 4500-466. The ergonomic controls and adjustable seat provide operators with a comfortable mowing experience. The reduced vibration and improved suspension system offer a smooth ride, even over uneven terrain. This attention to user comfort is essential, especially for those who spend extended periods mowing.

Another significant feature is the machine's advanced drive mechanics. The dual hydrostatic drive system ensures smooth handling and intuitive control, making it easy to maneuver around obstacles and tight spaces. The zero-turn capability allows for precise navigation and enhances productivity, significantly reducing mowing time.

In terms of durability, the Exmark 4500-466 is built to withstand the rigors of frequent use. The heavy-duty frame and high-quality materials ensure that the mower can endure tough conditions while maintaining its performance. Regular maintenance is made easy through accessible components, ensuring owners can keep their mower in top condition with minimal effort.

In conclusion, the Exmark 4500-466 represents the pinnacle of zero-turn mower technology. With its powerful engine, advanced cutting systems, user-centric design, and robust construction, it offers everything needed for effective lawn care. Whether you're a professional landscaper or a homeowner looking for a reliable mowing solution, the Exmark 4500-466 is a worthy investment that will exceed expectations.