Exmark VT730EKC524, VT691KA484CA, VT691KA524 Adjusting the Cutting Height, Transporting a Unit

Page 24

Operation

Adjusting the Cutting Height

The cutting height of the mower deck is adjusted from 1 to 5 inches (2.5 cm to 12.7 cm) in 1/4 inch (6.4 mm) increments.

1.Stop the machine and move the motion control levers to the neutral position.

2.Disengage the PTO.

3.Raise and lock the deck to the 5 inch (12.7 cm) transport position.

The deck is raised by pulling the deck lift handle rearward and to the right to place it into the transport lock position.

Figure 15

1. Height adjustment pin

3. Deck lift handle

2.Height of cut holes

Figure 14

1.

Transport lock position

3.

Front reference/speed

 

 

 

control bar

2.

RH Motion control lever

4.

Deck lift handle

Note: When changing the cutting height positions, always come to a complete stop and disengage the PTO.

4.Insert the height adjustment pin into the hole corresponding to the desired cutting height.

See the decal on the side of the deck lift plate for cut heights (reference Figure 15).

5.Pull the deck lift handle rearward and to the left and slowly allow the deck to lower to the cutting height.

Transporting

Transporting a Unit

Use a heavy-duty trailer or truck to transport the machine. Lock brake and block wheels. Securely fasten the machine to the trailer or truck with straps, chains, cable, or ropes. Be sure that the trailer or truck has all necessary lighting and marking as required by law. Secure a trailer with a safety chain.

CAUTION

This unit does not have proper turn signals, lights, reflective markings, or a slow moving vehicle emblem. Driving on a street or roadway without such equipment is dangerous and can lead to accidents causing personal injury. Driving on a street or roadway without such equipment may also be a violation of State laws and the operator may be subject to traffic tickets and/or fines.

Do Not drive a unit on a public street or roadway.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Vantage California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 116-0404 116-2040 116-3076 116-7217 116-5040 116-4648 Specifications Model NumbersSystems Dimensions Curb Weight Product OverviewTorque Requirements Tread Width Outside to OutsideOperation ControlsIgnition Switch Park Brake LeverHour Meter Fuel Shut-Off ValvePre-Start Operating InstructionsPTO Engagement Disengaging the PTOStopping the Engine Driving the Machine Driving ForwardAdjusting the Front Reference/Speed Control Bar Operating the PlatformOperating the Machine with the Platform Up Operating the Machine with the Platform DownAdjusting the Cutting Height TransportingTransporting a Unit Loading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Release the Cushion for Rear Access Check Mower BladesCheck Safety Interlock System Blade control switch PTO is pulled onService Air Cleaner Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsCheck Spark Plugs Change Fuel FilterChange Hydraulic System Filter and Fluid Hydraulic System Air Purge LevelWheel Hub Nut Torque Specification Check Spark Arrester if equippedThread Locking Adhesives Mobil HTS Grease Or Food-Grade Anti-seizeCopper-Based Anti-seize Dielectric GreaseAdjusting the Cutting Deck Rake Adjusting the Rear of the Deck Park Brake AdjustmentPump Drive Belt Tension Mower Deck Drive Belt TensionChecking the Tire Pressure in Drive System Electric Clutch Adjustment Removing the ShimMotion Control Neutral Adjustment Motion Control Tracking Adjustment Check the Neutral Switch AlignmentAdjust RH Motion Control Handle Position Caster Pivot Bearings Pre-Load Adjustment Clean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsClean Debris From Machine Clean Grass Build-Up Under DeckBattery Disposal Troubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Schematics Electrical Diagram-All Units Except Kohler EFIElectrical Diagram-Kohler EFI Electrical Schematic-All Units Except Kohler EFI Electrical Schematic-Kohler EFI Hydraulic Diagram General Warranty Conditions and Products Covered Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use Exmark Accessories and Options

VT691KA524CA, VT691KA484CA, VT651KA484, VT730EKC524, VT691KA524 specifications

The Exmark VT691KA524, VT730EKC524, VT651KA484, VT691KA484CA, and VT691KA524CA mowers represent some of the most advanced lawn care technology in the market. Each model is designed to deliver professional-grade performance, ensuring lawns are impeccably manicured.

The VT691KA524 features a robust 691cc engine, delivering powerful performance. Its 52-inch cutting deck allows for efficient mowing, making it ideal for medium to large-sized lawns. The mower incorporates Exmark's innovative patented UltraCut deck design, which offers exceptional cut quality and reduced clumping. Additionally, it boasts a high-capacity fuel tank, which is designed for extended operation without frequent refueling.

Another standout model, the VT730EKC524, comes with a 730cc engine, providing even more horsepower. This model supports advanced cooling and air filtration systems that enhance engine life and performance. The VT730EKC524’s fully adjustable cutting height options allow users to customize their mowing experience, ensuring a clean and even cut on various grass types.

The VT651KA484, equipped with a 651cc engine, emphasizes manoeuvrability and ease of use. It features a compact design that allows it to navigate tight spaces. The 48-inch cutting deck still provides a significant mowing width, and the model is also equipped with Exmark’s patented parking brake system for added safety.

The VT691KA484CA and VT691KA524CA are both equipped with the powerful 691cc engine like the VT691KA524. However, they come with unique functionalities that enhance their usability. The -CA variants offer additional features, such as an improved comfort seat and steering controls, making them ideal for extended mowing sessions without fatigue.

All these models feature Exmark’s signature Precision-Theory mower technology. This ensures that the mower maintains a consistent speed and cutting height while preventing scalping on uneven terrain. Furthermore, the mowers are constructed with durable, high-quality materials designed for longevity, ensuring that they can withstand the rigors of regular use.

With their user-friendly operation, advanced technologies, and rugged construction, the Exmark VT series mowers are an excellent investment for anyone looking to maintain an attractive and healthy lawn. Whether you choose the VT691KA524 for its efficiency or the VT730EKC524 for its superior horsepower, each model guarantees professional-quality results.
Top Page Image Contents