Exmark VT691KA524CA, VT651KA484 Check for Loose Hardware, Service Air Cleaner, Change Engine Oil

Page 31

Maintenance

5.Move the right side motion control lever to the center, operating position.

6.Continue holding the right side motion control lever in the center, operating position and pull up on the blade control switch (PTO) and release. The clutch should engage and the mower blades begin rotating.

7.Move or release the right side motion control lever into the neutral position. The blades should stop rotating and the engine should continue running.

8.Push the blade control switch down and move the right side motion control lever to the center, operating position.

9.Continue holding the right side motion control lever in the center, operating position and pull up on the blade control switch (PTO) and release. The clutch should engage and the mower blades begin rotating.

10.Push the blade control switch (PTO) down to the off position. The blades should stop rotating.

11.With the engine running, pull up the blade control switch (PTO) and release without holding right side motion control lever to the center, operating position. The blades should not rotate.

Check for Loose Hardware

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Visually inspect machine for any loose hardware or any other possible problem. Tighten hardware or correct the problem before operating.

Service Air Cleaner

Service Interval: Every 250 hours—Replace the primary air cleaner element — check secondary air cleaner element; replace if dirty. (May need more often under severe conditions. See the Engine manual for additional information.)

Every 500 hours—

Replace the secondary

air cleaner element. (May need more often under severe conditions. See the Engine manual for additional information.)

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.See the Engine Owner's Manual for maintenance instructions.

Change Engine Oil

Service Interval: After the first 5 hours

Every 100 hours (May need more often under severe conditions.)

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Drain oil while engine is warm from operation.

3.The oil drain hose assembly is located on the left side of the engine.

Place pan under machine to catch oil. Remove oil drain plug. Allow oil to drain and replace oil drain plug. Torque plug to 20-24 ft-lb (27-33 N-m).

4.Replace the oil filter per the Engine Owner's Manual. Clean around the oil filter and carefully remove the filter by unscrewing it. Make sure no oil drains onto the belt drive or clutch through the holes in the engine deck. Before the new filter is installed, apply a thin coating of Exmark 4–Cycle Premium Engine Oil on the surface of the rubber seal. Turn filter clockwise until rubber seal contacts the filter adapter, then tighten filter an additional 2/3 to 3/4 turn.

5.Clean around oil fill cap and remove cap. Fill to specified capacity and replace cap.

6.Use oil recommended in the Check Engine Oil Level section. Do Not overfill. Start the engine and check for leaks. Stop engine and recheck oil level.

7.Wipe up any spilled oil from engine deck mounting surfaces.

Check Hydraulic Oil Level

Service Interval: Every 50 hours

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Vantage California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals 116-0404 116-2040 116-3076 116-7217 116-5040 116-4648 Model Numbers SpecificationsSystems Dimensions Tread Width Outside to Outside Curb WeightProduct Overview Torque RequirementsControls OperationFuel Shut-Off Valve Ignition SwitchPark Brake Lever Hour MeterOperating Instructions Pre-StartDisengaging the PTO PTO EngagementStopping the Engine Driving Forward Driving the MachineOperating the Platform Adjusting the Front Reference/Speed Control BarOperating the Machine with the Platform Down Operating the Machine with the Platform UpTransporting Adjusting the Cutting HeightTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Check Mower Blades Release the Cushion for Rear AccessBlade control switch PTO is pulled on Check Safety Interlock SystemCheck Hydraulic Oil Level Service Air CleanerCheck for Loose Hardware Change Engine OilLubricate Caster Wheel Hubs Check Tire PressuresCheck Condition Of Belts Lubricate Grease FittingsChange Fuel Filter Check Spark PlugsChange Hydraulic System Filter and Fluid Level Hydraulic System Air PurgeCheck Spark Arrester if equipped Wheel Hub Nut Torque SpecificationDielectric Grease Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Copper-Based Anti-seizeAdjusting the Cutting Deck Rake Mower Deck Drive Belt Tension Adjusting the Rear of the DeckPark Brake Adjustment Pump Drive Belt TensionChecking the Tire Pressure in Drive System Removing the Shim Electric Clutch AdjustmentMotion Control Neutral Adjustment Check the Neutral Switch Alignment Motion Control Tracking AdjustmentAdjust RH Motion Control Handle Position Caster Pivot Bearings Pre-Load Adjustment Clean Grass Build-Up Under Deck Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineBattery Disposal Problem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram-All Units Except Kohler EFI SchematicsElectrical Diagram-Kohler EFI Electrical Schematic-All Units Except Kohler EFI Electrical Schematic-Kohler EFI Hydraulic Diagram General Warranty Conditions and Products Covered Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use Exmark Accessories and Options

VT691KA524CA, VT691KA484CA, VT651KA484, VT730EKC524, VT691KA524 specifications

The Exmark VT691KA524, VT730EKC524, VT651KA484, VT691KA484CA, and VT691KA524CA mowers represent some of the most advanced lawn care technology in the market. Each model is designed to deliver professional-grade performance, ensuring lawns are impeccably manicured.

The VT691KA524 features a robust 691cc engine, delivering powerful performance. Its 52-inch cutting deck allows for efficient mowing, making it ideal for medium to large-sized lawns. The mower incorporates Exmark's innovative patented UltraCut deck design, which offers exceptional cut quality and reduced clumping. Additionally, it boasts a high-capacity fuel tank, which is designed for extended operation without frequent refueling.

Another standout model, the VT730EKC524, comes with a 730cc engine, providing even more horsepower. This model supports advanced cooling and air filtration systems that enhance engine life and performance. The VT730EKC524’s fully adjustable cutting height options allow users to customize their mowing experience, ensuring a clean and even cut on various grass types.

The VT651KA484, equipped with a 651cc engine, emphasizes manoeuvrability and ease of use. It features a compact design that allows it to navigate tight spaces. The 48-inch cutting deck still provides a significant mowing width, and the model is also equipped with Exmark’s patented parking brake system for added safety.

The VT691KA484CA and VT691KA524CA are both equipped with the powerful 691cc engine like the VT691KA524. However, they come with unique functionalities that enhance their usability. The -CA variants offer additional features, such as an improved comfort seat and steering controls, making them ideal for extended mowing sessions without fatigue.

All these models feature Exmark’s signature Precision-Theory mower technology. This ensures that the mower maintains a consistent speed and cutting height while preventing scalping on uneven terrain. Furthermore, the mowers are constructed with durable, high-quality materials designed for longevity, ensuring that they can withstand the rigors of regular use.

With their user-friendly operation, advanced technologies, and rugged construction, the Exmark VT series mowers are an excellent investment for anyone looking to maintain an attractive and healthy lawn. Whether you choose the VT691KA524 for its efficiency or the VT730EKC524 for its superior horsepower, each model guarantees professional-quality results.
Top Page Image Contents