Exmark VT691KA484CA, VT691KA524CA, VT651KA484, VT730EKC524 manual Adjusting the Cutting Deck Rake

Page 37

Maintenance

4. Check and adjust the side to side blade level if you have not checked the setting; refer to Deck Leveling.

5. Carefully rotate the blades front to rear (Figure 24). Measure from the tip of the front blade to the level surface and the tip of the rear blade to the level surface on all blades. The blades should be 1/4 inch (6.4 mm) lower in the front than in the rear.

Figure 22

1. Blades front to rear

2. Measure here

7. Measure between the outside cutting edges and the flat surface (Figure 23). If both measurements are not within 3/16 inch (5 mm), an adjustment is required; contact an Authorized Service Dealer.

Figure 24

1. Blades front to rear

2. Measure here

6. Loosen the rear lock nuts on both adjustment rods (Figure 25).

Figure 23

1. Blades side to side

2. Measure here

8. Lower the discharge deflector.

Adjusting the Cutting Deck Rake

1.Park the machine on a level surface and disengage the blade control switch.

2.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

3.Check the air pressure in the drive tires. If needed, adjust to the recommended inflation; refer to Checking the Tire Pressure in Drive System Maintenance section.

Figure 25

1. Adjustment rod

3. Front lock nut

2. Rear lock nut

Note: Make sure the engine deck brackets are resting firmly on the rear lift points (see Figure 26). If it is lifting off, tighten the front locknut of the adjusting rod on the opposite side.

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Vantage California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals 116-0404 116-2040 116-3076 116-7217 116-5040 116-4648 Model Numbers SpecificationsSystems Dimensions Product Overview Curb WeightTorque Requirements Tread Width Outside to OutsideControls OperationPark Brake Lever Ignition SwitchHour Meter Fuel Shut-Off ValveOperating Instructions Pre-StartDisengaging the PTO PTO EngagementStopping the Engine Driving Forward Driving the MachineOperating the Platform Adjusting the Front Reference/Speed Control BarOperating the Machine with the Platform Down Operating the Machine with the Platform UpTransporting Adjusting the Cutting HeightTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Check Mower Blades Release the Cushion for Rear AccessBlade control switch PTO is pulled on Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerChange Engine Oil Check Hydraulic Oil LevelCheck Condition Of Belts Check Tire PressuresLubricate Grease Fittings Lubricate Caster Wheel HubsChange Fuel Filter Check Spark PlugsChange Hydraulic System Filter and Fluid Level Hydraulic System Air PurgeCheck Spark Arrester if equipped Wheel Hub Nut Torque SpecificationMobil HTS Grease Or Food-Grade Anti-seize Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseAdjusting the Cutting Deck Rake Park Brake Adjustment Adjusting the Rear of the DeckPump Drive Belt Tension Mower Deck Drive Belt TensionChecking the Tire Pressure in Drive System Removing the Shim Electric Clutch AdjustmentMotion Control Neutral Adjustment Check the Neutral Switch Alignment Motion Control Tracking AdjustmentAdjust RH Motion Control Handle Position Caster Pivot Bearings Pre-Load Adjustment Remove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Debris From Machine Clean Grass Build-Up Under DeckBattery Disposal Problem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram-All Units Except Kohler EFI SchematicsElectrical Diagram-Kohler EFI Electrical Schematic-All Units Except Kohler EFI Electrical Schematic-Kohler EFI Hydraulic Diagram General Warranty Conditions and Products Covered Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use Exmark Accessories and Options

VT691KA524CA, VT691KA484CA, VT651KA484, VT730EKC524, VT691KA524 specifications

The Exmark VT691KA524, VT730EKC524, VT651KA484, VT691KA484CA, and VT691KA524CA mowers represent some of the most advanced lawn care technology in the market. Each model is designed to deliver professional-grade performance, ensuring lawns are impeccably manicured.

The VT691KA524 features a robust 691cc engine, delivering powerful performance. Its 52-inch cutting deck allows for efficient mowing, making it ideal for medium to large-sized lawns. The mower incorporates Exmark's innovative patented UltraCut deck design, which offers exceptional cut quality and reduced clumping. Additionally, it boasts a high-capacity fuel tank, which is designed for extended operation without frequent refueling.

Another standout model, the VT730EKC524, comes with a 730cc engine, providing even more horsepower. This model supports advanced cooling and air filtration systems that enhance engine life and performance. The VT730EKC524’s fully adjustable cutting height options allow users to customize their mowing experience, ensuring a clean and even cut on various grass types.

The VT651KA484, equipped with a 651cc engine, emphasizes manoeuvrability and ease of use. It features a compact design that allows it to navigate tight spaces. The 48-inch cutting deck still provides a significant mowing width, and the model is also equipped with Exmark’s patented parking brake system for added safety.

The VT691KA484CA and VT691KA524CA are both equipped with the powerful 691cc engine like the VT691KA524. However, they come with unique functionalities that enhance their usability. The -CA variants offer additional features, such as an improved comfort seat and steering controls, making them ideal for extended mowing sessions without fatigue.

All these models feature Exmark’s signature Precision-Theory mower technology. This ensures that the mower maintains a consistent speed and cutting height while preventing scalping on uneven terrain. Furthermore, the mowers are constructed with durable, high-quality materials designed for longevity, ensuring that they can withstand the rigors of regular use.

With their user-friendly operation, advanced technologies, and rugged construction, the Exmark VT series mowers are an excellent investment for anyone looking to maintain an attractive and healthy lawn. Whether you choose the VT691KA524 for its efficiency or the VT730EKC524 for its superior horsepower, each model guarantees professional-quality results.
Top Page Image Contents