Exmark VT651KA484, VT691KA484CA, VT691KA524CA, VT730EKC524 Adjust RH Motion Control Handle Position

Page 43

Maintenance

6.Check the alignment on the LH and RH neutral switches upper and lower surfaces (reference Figure 39). If they are not in alignment, loosen the hardware on the lower neutral switch and adjust it forward or rearward as necessary. Once aligned, tighten the hardware. Check the neutral switch alignment again as the deck is moved through the highest and lowest cut height setting; adjust the lower neutral switch surface if necessary.

B.If the indicator does not stay lit while moving the deck up and down, contact an Authorized Service Dealer. Remove the key.

Adjust RH Motion Control Handle Position

If the motion control levers do not align horizontally, adjust the right side motion control lever.

Note: Adjust the horizontal alignment before the front to back alignment.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Push the right motion control lever down out of locked neutral position.

3.Check if it aligns horizontally with the left motion control lever.

Figure 39

1.

Alignment reference

4.

Lower neutral switch

 

 

 

surface

2.

Upper neutral switch

5.

Hardware

 

surface

 

 

3.Switch mounting plate

7.Adjust the upper neutral switch surface left or right if side-to-side alignment is needed. The upper and lower switches should be as close together as possible without touching (approximately .06 inch (1.5 mm) gap is desirable). The switch mounting plate can be moved up or down to adjust the position of the lower neutral switch.

8.Check the function of the neutral switches by temporarily replacing the key. With the engine off, turn the ignition switch to the “ON” position. Locate the LCD indicator in the message display. Raise and lower the deck.

A.If the indicator displays while moving the deck up and down, the neutral switches have been adjusted properly and no further adjustment is necessary.

Figure 40

1.LH Motion control lever

2.RH Motion control lever

3.RH Motion control lever in PTO disengaged position

4.Check the horizontal alignment here

4.To adjust the right motion control lever horizontally, the cam needs to be adjusted.

5.Release the cushion from the rear of the machine.

6.Loosen the nut and bolt holding the cam.

7.Adjust the cam until it aligns with the left motion control lever and tighten the nut and bolt for the cam.

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Vantage California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals 116-0404 116-2040 116-3076 116-7217 116-5040 116-4648 Model Numbers SpecificationsSystems Dimensions Tread Width Outside to Outside Curb WeightProduct Overview Torque RequirementsControls OperationFuel Shut-Off Valve Ignition SwitchPark Brake Lever Hour MeterOperating Instructions Pre-StartDisengaging the PTO PTO EngagementStopping the Engine Driving Forward Driving the MachineOperating the Platform Adjusting the Front Reference/Speed Control BarOperating the Machine with the Platform Down Operating the Machine with the Platform UpTransporting Adjusting the Cutting HeightTransporting a Unit Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Check Mower Blades Release the Cushion for Rear AccessBlade control switch PTO is pulled on Check Safety Interlock SystemCheck Hydraulic Oil Level Service Air CleanerCheck for Loose Hardware Change Engine OilLubricate Caster Wheel Hubs Check Tire PressuresCheck Condition Of Belts Lubricate Grease FittingsChange Fuel Filter Check Spark PlugsChange Hydraulic System Filter and Fluid Level Hydraulic System Air PurgeCheck Spark Arrester if equipped Wheel Hub Nut Torque SpecificationDielectric Grease Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Copper-Based Anti-seizeAdjusting the Cutting Deck Rake Mower Deck Drive Belt Tension Adjusting the Rear of the DeckPark Brake Adjustment Pump Drive Belt TensionChecking the Tire Pressure in Drive System Removing the Shim Electric Clutch AdjustmentMotion Control Neutral Adjustment Check the Neutral Switch Alignment Motion Control Tracking AdjustmentAdjust RH Motion Control Handle Position Caster Pivot Bearings Pre-Load Adjustment Clean Grass Build-Up Under Deck Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineBattery Disposal Problem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram-All Units Except Kohler EFI SchematicsElectrical Diagram-Kohler EFI Electrical Schematic-All Units Except Kohler EFI Electrical Schematic-Kohler EFI Hydraulic Diagram General Warranty Conditions and Products Covered Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use Exmark Accessories and Options

VT691KA524CA, VT691KA484CA, VT651KA484, VT730EKC524, VT691KA524 specifications

The Exmark VT691KA524, VT730EKC524, VT651KA484, VT691KA484CA, and VT691KA524CA mowers represent some of the most advanced lawn care technology in the market. Each model is designed to deliver professional-grade performance, ensuring lawns are impeccably manicured.

The VT691KA524 features a robust 691cc engine, delivering powerful performance. Its 52-inch cutting deck allows for efficient mowing, making it ideal for medium to large-sized lawns. The mower incorporates Exmark's innovative patented UltraCut deck design, which offers exceptional cut quality and reduced clumping. Additionally, it boasts a high-capacity fuel tank, which is designed for extended operation without frequent refueling.

Another standout model, the VT730EKC524, comes with a 730cc engine, providing even more horsepower. This model supports advanced cooling and air filtration systems that enhance engine life and performance. The VT730EKC524’s fully adjustable cutting height options allow users to customize their mowing experience, ensuring a clean and even cut on various grass types.

The VT651KA484, equipped with a 651cc engine, emphasizes manoeuvrability and ease of use. It features a compact design that allows it to navigate tight spaces. The 48-inch cutting deck still provides a significant mowing width, and the model is also equipped with Exmark’s patented parking brake system for added safety.

The VT691KA484CA and VT691KA524CA are both equipped with the powerful 691cc engine like the VT691KA524. However, they come with unique functionalities that enhance their usability. The -CA variants offer additional features, such as an improved comfort seat and steering controls, making them ideal for extended mowing sessions without fatigue.

All these models feature Exmark’s signature Precision-Theory mower technology. This ensures that the mower maintains a consistent speed and cutting height while preventing scalping on uneven terrain. Furthermore, the mowers are constructed with durable, high-quality materials designed for longevity, ensuring that they can withstand the rigors of regular use.

With their user-friendly operation, advanced technologies, and rugged construction, the Exmark VT series mowers are an excellent investment for anyone looking to maintain an attractive and healthy lawn. Whether you choose the VT691KA524 for its efficiency or the VT730EKC524 for its superior horsepower, each model guarantees professional-quality results.
Top Page Image Contents