Exmark 920 manual Engaging the PTO, Disengaging the PTO, Stopping the Engine, Driving the Machine

Page 26

Operation

attempts. Failure to follow these guidelines can burn out the starter motor.

7.If the choke is in the “ON” position, gradually return choke to the “OFF” position as the engine warms up.

Engaging the PTO

DANGER

The rotating blades under the mower deck are dangerous. Blade contact can cause serious injury or kill you.

Do Not put hands or feet under the mower or mower deck when the blades are engaged.

DANGER

An uncovered discharge opening will allow objects to be thrown in an operator’s or bystander’s direction. Also, contact with the blade could occur. Thrown objects or blade contact can cause serious injury or death.

Never operate the mower with the discharge deflector raised, removed, or altered unless there is a grass collection system or mulch kit in place and working properly.

The PTO push-pull switch engages the cutting blades. Be sure that all persons are clear of the mower deck and discharge area before engaging PTO.

Important: Operator must be in seat before the PTO can be engaged.

1.Set the throttle midway between the “SLOW” and “FAST” positions.

2.Pull the PTO switch outward to engage the blades.

3.Place the throttle in the “FAST” position to begin mowing.

Disengaging the PTO

1.Set the throttle midway between the “SLOW” and “FAST” positions.

2.Push the PTO switch in to disengage the blades.

Stopping the Engine

1. Bring the unit to a full stop.

2.Move the motion control levers out to the neutral lock position.

3.Engage the parking brake.

4.Place the throttle midway between the “SLOW” and “FAST” positions.

5.Disengage the PTO.

6.Allow the engine to run for a minimum of 15 seconds, then turn the ignition switch to the “OFF” position to stop the engine.

7.Remove the key to prevent children or other unauthorized persons from starting engine.

8.Close the fuel shut-off valve when the machine will not be in use for a few days, when transporting, or when the unit is parked inside a building.

Driving the Machine

CAUTION

Machine can spin very rapidly by positioning one lever too much ahead of the other. Operator may lose control of the machine, which may cause damage to the machine or injury.

Use caution when making turns.

Slow the machine down before making sharp turns.

Important: To begin movement (forward or backward) the operator must be in the seat, the brake lever must be disengaged (pushed down) before the motion control levers can be moved in or the engine will stop.

When the motion control levers are positioned fully outward (apart) in the T-slot, the drive system is in the neutral lock position (Figure 14).

Note: The “N” LCD indicator appears when both levers are in the neutral lock position.

When the motion control levers are moved directly inward (together) the drive system is in the neutral operate position.

26

Image 26
Contents Lazer Z S-SERIES California Introduction Contents Safe Operating Practices SafetySafety Alert Symbol TrainingSafety Operation Using the Rollover Protection System Rops Slope OperationMaintenance and Storage For Kohler EFI Electronic Fuel Injection Units Safety and Instructional Decals 109-7232 109-8483 116-0752 PTO Switch Symbols Systems SpecificationsModel Numbers Tires & Wheels SeatHydrostatic Ground Drive System Cutting DeckOverall Length DimensionsOverall Width Overall HeightWheel Base Center of Caster Tire to Center of Drive Tire Curb WeightTread Width Center to Center of Tires, Widthwise Accessory Weight Table Worksheet Torque RequirementsControls Product OverviewOperation Motion Control LeversThrottle Control Ignition SwitchChoke Control All Units Except Kohler EFI Brake LeverDrive Wheel Release Valves Fuel Shut-Off ValveFuel Gauge Pre-Start Open the Fuel Shut-Off Valve Operating InstructionsRaise the Rollover Protection System Rops Starting the EngineStopping the Engine Engaging the PTODisengaging the PTO Driving the MachineAdjusting the Cutting Height Driving ForwardAdjusting the Anti-Scalp Rollers Loading a Unit TransportingTransporting a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Do Not jump start a weak battery if these conditions existCheck Mower Blades Check Seat Belt Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Knobs Change Engine Oil Service Air CleanerCheck for Loose Hardware Check Hydraulic Oil LevelLubricate Grease Fittings Check Tire PressuresCheck Condition Of Belts Lubricate Caster Wheel HubsCheck Spark Plugs Lubricate Brake Handle PivotLubricate Deck Lift Pivot Change Fuel FilterWheel Hub Slotted Nut Torque Specification Change Hydraulic System Filter and FluidCopper-Based Anti-seize Check Spark Arrester if equippedThread Locking Adhesives Dielectric GreaseAdjustments Deck LevelingPump Drive Belt Tension Deck Belt TensionAdjusting the Parking Brake Left Hand Brake ShownElectric Clutch Adjustment Removing the Shim Motion Control Linkage Adjustment Motion Control Handle Adjustment Motion Control Damper AdjustmentMotion Control Neutral Lock Pivot Adjustment Caster Pivot Bearings Pre-Load Adjustment Adjusting the TiltClean Hydro Fan Cooling Fins Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineBattery Disposal Troubleshooting Problem Possible Cause Corrective ActionSee Drive Wheel Release Valves section Troubleshooting Schematics Diagram All units except Kohler EFISchematics Electrical Logic Schematic All units except Kohler EFI Schematics Hydraulic Diagram General Warranty Conditions and Products Covered Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 43.2 Kb Manual 52 pages 8.82 Kb

920 specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.