Exmark 920 manual Maintenance and Storage

Page 9

Safety

WARNING

There is no rollover protection when the roll bar is down. Wheels dropping over edges, ditches, steep banks, or water can cause rollovers, which may result in serious injury, death or drowning.

Keep the roll bar in the raised and locked position and use seat belt.

Lower the roll bar only when absolutely necessary.

Do Not wear seat belt when the roll bar is down.

Drive slowly and carefully.

Raise the roll bar as soon as clearance permits.

Check carefully for overhead clearances (i.e. branches, doorways, and electrical wires) before driving under any objects and Do Not contact them.

In the event of a rollover, take the unit to an Authorized Service Dealer to have the ROPS inspected.

Maintenance and Storage

Disengage drives, lower implement, set parking brake, stop engine and remove key or disconnect spark plug wire. Wait for all movement to stop before adjusting, cleaning or repairing.

Keep engine and engine area free from accumulation of grass, leaves, excessive grease or oil, and other debris which can accumulate in these areas. These materials can become combustible and may result in a fire.

Let engine cool before storing and Do Not store near flame or any enclosed area where open pilot lights or heat appliances are present.

Shut off fuel while storing or transporting. Do Not store fuel near flames or drain indoors.

Park machine on level ground. Never allow untrained personnel to service machine.

Use jack stands to support components when required.

Carefully release pressure from components with stored energy.

Disconnect battery or remove spark plug wire before making any repairs. Disconnect the negative terminal first and the positive last. Reconnect positive first and negative last.

Use care when checking blades. Wrap the blade(s) or wear gloves, and use caution when servicing them. Only replace damaged blades. Never straighten or weld them.

Keep hands and feet away from moving parts. If possible, Do Not make adjustments with the engine running.

Charge batteries in an open well ventilated area, away from spark and flames. Unplug charger before connecting or disconnecting from battery. Wear protective clothing and use insulated tools.

DANGER

Charging or jump starting the battery may produce explosive gases. Battery gases can explode causing serious injury.

Keep sparks, flames, or cigarettes away from battery.

Ventilate when charging or using battery in an enclosed space.

Make sure venting path of battery is always open once battery is filled with acid.

Always shield eyes and face from battery.

DANGER

Battery electrolyte contains sulfuric acid, which is poisonous and can cause severe burns. Swallowing electrolyte can be fatal or if it touches skin can cause severe burns.

Wear safety glasses to shield eyes, and rubber gloves to protect skin and clothing when handling electrolyte.

Do Not swallow electrolyte.

In the event of an accident, flush with water and call a doctor immediately.

9

Image 9
Contents Lazer Z S-SERIES California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage For Kohler EFI Electronic Fuel Injection Units Safety and Instructional Decals 109-7232 109-8483 116-0752 PTO Switch Symbols Specifications Model NumbersSystems Hydrostatic Ground Drive System SeatTires & Wheels Cutting DeckOverall Width DimensionsOverall Length Overall HeightCurb Weight Tread Width Center to Center of Tires, WidthwiseWheel Base Center of Caster Tire to Center of Drive Tire Torque Requirements Accessory Weight Table WorksheetOperation Product OverviewControls Motion Control LeversChoke Control All Units Except Kohler EFI Ignition SwitchThrottle Control Brake LeverFuel Shut-Off Valve Fuel GaugeDrive Wheel Release Valves Pre-Start Raise the Rollover Protection System Rops Operating InstructionsOpen the Fuel Shut-Off Valve Starting the EngineDisengaging the PTO Engaging the PTOStopping the Engine Driving the MachineDriving Forward Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Transporting Transporting a UnitLoading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeDo Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Check Safety Interlock System Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose Hardware Service Air CleanerChange Engine Oil Check Hydraulic Oil LevelCheck Condition Of Belts Check Tire PressuresLubricate Grease Fittings Lubricate Caster Wheel HubsLubricate Deck Lift Pivot Lubricate Brake Handle PivotCheck Spark Plugs Change Fuel FilterChange Hydraulic System Filter and Fluid Wheel Hub Slotted Nut Torque SpecificationThread Locking Adhesives Check Spark Arrester if equippedCopper-Based Anti-seize Dielectric GreaseDeck Leveling AdjustmentsDeck Belt Tension Pump Drive Belt TensionLeft Hand Brake Shown Adjusting the Parking BrakeElectric Clutch Adjustment Removing the Shim Motion Control Linkage Adjustment Motion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Adjusting the Tilt Caster Pivot Bearings Pre-Load AdjustmentRemove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Fins Clean Debris From MachineBattery Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Diagram All units except Kohler EFI SchematicsSchematics Electrical Logic Schematic All units except Kohler EFI Schematics Hydraulic Diagram General Warranty Conditions and Products Covered Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 43.2 Kb Manual 52 pages 8.82 Kb

920 specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.