Exmark 920 manual This page may be copied for personal use

Page 63

Figure 42

This page may be copied for personal use.

1.The maximum slope you can safely operate the machine on is 15 degrees. Use the slope indicator to determine the degree of slope of hills before operating. Do Not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope.

2.Align this edge with a vertical surface, a tree, building, fence pole, etc.

3.Example of how to compare slope with folded edge.

63

Page 62 Page 64
Image 63
Page 62 Page 64
Contents
Lazer Z S-SERIES California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Operation Slope Operation Using the Rollover Protection System RopsMaintenance and Storage For Kohler EFI Electronic Fuel Injection Units Safety and Instructional Decals 109-7232 109-8483 116-0752 PTO Switch Symbols Specifications Model NumbersSystems Cutting Deck SeatHydrostatic Ground Drive System Tires & WheelsOverall Height DimensionsOverall Width Overall LengthCurb Weight Tread Width Center to Center of Tires, WidthwiseWheel Base Center of Caster Tire to Center of Drive Tire Torque Requirements Accessory Weight Table WorksheetMotion Control Levers Product OverviewOperation ControlsBrake Lever Ignition SwitchChoke Control All Units Except Kohler EFI Throttle ControlFuel Shut-Off Valve Fuel GaugeDrive Wheel Release Valves Pre-Start Starting the Engine Operating InstructionsRaise the Rollover Protection System Rops Open the Fuel Shut-Off ValveDriving the Machine Engaging the PTODisengaging the PTO Stopping the EngineDriving Forward Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Transporting Transporting a UnitLoading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeDo Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Check Safety Interlock System Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check Hydraulic Oil Level Service Air CleanerCheck for Loose Hardware Change Engine OilLubricate Caster Wheel Hubs Check Tire PressuresCheck Condition Of Belts Lubricate Grease FittingsChange Fuel Filter Lubricate Brake Handle PivotLubricate Deck Lift Pivot Check Spark PlugsChange Hydraulic System Filter and Fluid Wheel Hub Slotted Nut Torque SpecificationDielectric Grease Check Spark Arrester if equippedThread Locking Adhesives Copper-Based Anti-seizeDeck Leveling AdjustmentsDeck Belt Tension Pump Drive Belt TensionLeft Hand Brake Shown Adjusting the Parking BrakeElectric Clutch Adjustment Removing the Shim Motion Control Linkage Adjustment Motion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Adjusting the Tilt Caster Pivot Bearings Pre-Load AdjustmentClean Debris From Machine Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Hydro Fan Cooling FinsBattery Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Diagram All units except Kohler EFI SchematicsSchematics Electrical Logic Schematic All units except Kohler EFI Schematics Hydraulic Diagram General Warranty Conditions and Products Covered Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 43.2 Kb Manual 52 pages 8.82 Kb
Top Page Image Contents