Exmark 850 manual Specifications, Model Numbers, Systems

Page 15

Specifications

Specifications

Model Numbers

Serial Nos: 850,000 and Higher

LZA20KAS484; LZA20KAX484; LZA20KAX524

Systems

Engine

Engine Specifications: See your Engine Owner’s Manual

RPM: Full Speed: 3750 ±50 RPM (PTO not

engaged) Idle: 1500 ±100 RPM

Fuel System

Capacity: 8.0 gal. (30.3 L)

Type of Fuel: Regular unleaded gasoline, 87 octane or higher; containing no more than 10% methanol or ethanol.

Fuel Filter: Kawasaki Kawasaki P/N 49019-7005

Fuel Shut-Off Valve:

All Units: 1/4 turn increments (“ON”, “OFF”).

Fuel level eight segment display — right hand control panel.

Low fuel indicator light.

Safety Interlock System

LCD indicators appear for the PTO, park brake, drive levers, and operator presence in the message display on the RH control panel.

PTO must be disengaged, brake engaged, and motion control levers out (neutral lock) to start engine. (It is not necessary for the operator to be in the seat to start the engine.)

Operator must be in seat when PTO is engaged, brake is disengaged, or motion control levers are moved in or engine will stop.

Engine will stop if either the left, the right, or both levers are moved from neutral lock position while brake is engaged.

Operator Controls

Steering and Motion Control:

Note: Motion control levers are adjustable to two heights.

Separate levers, on each side of the console, control speed and direction of travel of the respective drive wheels.

Electrical System

– Steering is controlled by varying the position

Charging System: Flywheel Alternator

of the levers relative to each other.

Charging Capacity: Kawasaki: 15 amps

– Moving motion control levers outward (in

Battery Type: BCI Group U1

slots) locks the drive system in neutral.

• Recommended Minimum Battery CCA: 260 CCA

• PTO Engagement Switch: Engages electric clutch

• Battery Voltage: 12 Volt

(to drive belt) which engages mower blades.

 

• Low Voltage Light — RH control panel

• Parking Brake Lever: Engages parking brake.

 

Polarity: Negative Ground

Fuses: All units:

25 amp main fuse

25 amp charging system fuse

10 amp PTO fuse

15 amp accessory fuse

Parking Brake Release Button: Releases parking brake.

Deck Height Adjustment Lever: Sets cutting height to desired position.

Deck Lift Pedal: Foot pedal that lifts deck.

Transport Lock:

Latching position: Automatically latches at the transport position.

15

Image 15
Contents Lazer Z Advantage Series Models California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationUsing the Rollover Protection System Rops Maintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 Message Display Specifications Model NumbersSystems Cutting Deck SeatHydrostatic Ground Drive System Tires & WheelsTorque Requirements DimensionsProduct Overview Controls OperationFuel Gauge Ignition SwitchHour Meter Fuel Shut-Off ValveDeck Lift Pedal PTO Engagement SwitchLow Voltage Indicator Drive Wheel Release ValvesPre-Start Operating InstructionsRaise the Rollover Protection System Rops Disengaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Engaging the PTOStopping the Engine Driving the MachineDriving Forward Driving in Reverse Adjusting the Cutting HeightAdjusting the Deck Lift Foot Pedal Adjusting the Anti-Scalp RollersTransporting Transporting a UnitDo Not drive a unit on a public street or roadway Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Battery Charge Check Engine Oil LevelProposition 65 Warning Do Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltCheck Hydraulic Oil Level Change Engine OilCheck Tire Pressures Check Condition Of Belts Lubricate Grease FittingsLubricate Caster Wheel Hubs Change Fuel Filter Lubricate Brake Handle PivotLubricate Deck Lift Pivot Check Spark PlugsWheel Hub Slotted Nut Torque Specification Style a black finishStyle B yellow zinc Dielectric Grease Check Spark Arrester if equippedThread Locking Adhesives Copper-Based Anti-seizeDeck Leveling AdjustmentsAdjusting the Parking Brake Pump Drive Belt TensionDeck Belt Tension Left Hand Brake Shown Removing the Shim Electric Clutch AdjustmentShim Motion Control Linkage Adjustment Adjusting the height Motion Control Damper AdjustmentMotion Control Handle Adjustment Motion Control Neutral Lock Pivot AdjustmentCaster Pivot Bearings Pre-Load Adjustment Motion Control Full Forward Tracking AdjustmentRemove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Debris From Machine Clean Grass Build-Up Under DeckBattery Disposal Problem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Troubleshooting Electrical Diagram SchematicsElectrical SchematicHydraulic Diagram Lazer Z Advantage Series Turf Equipment Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 48 pages 5.05 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 60 pages 43.2 Kb Manual 64 pages 1.01 Kb Manual 28 pages 32.2 Kb Manual 52 pages 62.21 Kb Manual 44 pages 57.61 Kb Manual 32 pages 16.59 Kb Manual 24 pages 21.56 Kb Manual 40 pages 46.04 Kb

0, 850 specifications

The Exmark 850 is a top-of-the-line commercial mower, known for its durability, efficiency, and advanced features, making it a favorite among landscaping professionals. With a powerful engine and innovative technology, the Exmark 850 is designed to tackle tough mowing tasks while ensuring a high-quality cut.

One of the standout characteristics of the Exmark 850 is its robust engine performance. Powered by a reliable Kohler or Kawasaki engine, it delivers exceptional horsepower, enabling it to handle various terrains and grass types with ease. The engine is designed for fuel efficiency, allowing operators to work longer hours without frequent refueling, ultimately boosting productivity on the job.

The cutting deck of the Exmark 850 is engineered with precision, utilizing Exmark's proprietary UltraCut technology. This technology ensures that grass is cut evenly and efficiently, resulting in a clean, manicured appearance. The deck height is easily adjustable, allowing users to quickly change settings to accommodate different lawn conditions and preferences.

Another key feature is the innovative suspension system that enhances ride quality. The Exmark 850 is equipped with a heavy-duty front axle and high-performance suspension that absorbs bumps and uneven ground, allowing for a smoother mowing experience. This is especially beneficial for operators who spend long hours on the mower, reducing fatigue and improving comfort.

Ergonomics play a crucial role in the design of the Exmark 850. The operator station is thoughtfully crafted with optimal controls and comfortable seating, allowing for easy maneuverability and long-term use. The ergonomic handles and intuitive control layout make it easy for operators to navigate tricky landscapes, enhancing overall efficiency.

In terms of durability, the Exmark 850 is built to withstand the rigors of commercial use. The high-quality materials and construction ensure that this mower can handle challenging conditions, extending its lifespan and reducing maintenance needs. Additionally, Exmark offers an extensive warranty program, providing peace of mind for operators.

Safety features are also prioritized in the Exmark 850, with guards and shields designed to protect the operator while mowers are in use. These features also include emergency shut-off systems and blade brake systems, ensuring compliance with safety standards.

Overall, the Exmark 850 stands out as a high-performing, reliable, and efficient mower suitable for a variety of commercial landscaping tasks. With its powerful engine, advanced cutting technology, ergonomic design, and emphasis on durability and safety, it continues to be a top choice for professionals seeking high-quality lawn care equipment.